| Sim No. |
Function |
| 1 |
1 |
Check the operation of the scanner (reading) unit and the control circuit |
| 2 |
Check the sensors in the scanner (reading) section and the related circuit |
| 5 |
Check the operation of the scanner (reading) unit and the control circuit |
| 2 |
1 |
Check the operation of the auto document feeder and the control circuit |
| 2 |
Check the operation of the sensors in the auto document feeder section and the control circuit |
| 3 |
Check the operation of the loads in the auto document feeder and the control circuit |
| 5 |
1 |
Check the operation of the display, LCD in the operation panel and the control circuit |
| 2 |
Check the operation of the heater lamp and the control circuit |
| 3 |
Check the operation of the scanner lamp and the control circuit |
| 4 |
Check the operation of the discharge lamp and the control circuit |
| 6 |
1 |
Check the operation of the loads in the paper transport system (clutches and solenoids) and the control circuit |
| 2 |
Check the operation of the each fan motor and the control circuit |
| 90 |
Set default position back to the factory setting (scanner is set to the lock enable position) |
| 7 |
1 |
Set the operating condition of aging |
| 6 |
Set the operating intermittent aging cycle |
| 8 |
Check the warm up time |
| 12 |
Set the document reading number of sheets (for aging operation) |
| 8 |
1 |
Check and adjust the operation of the developping voltage in each print mode and the control circuit |
| 2 |
Check and adjust the operation of the main charger voltage in each print mode and the control circuit |
| 6 |
Check and adjust the operation of the transport voltage and the control circuit |
| 9 |
2 |
Check the operation of the sensors in the paper reverse section (duplex section) and the control circuit |
| 3 |
Check the operation of the loads in the paper reverse section (duplex section) and the control circuit |
| 10 |
1 |
Check the operation of the toner supply mechanism (toner motor) and the control circuit |
| 4 |
Toner cartridge motor count sensor check |
| 14 |
|
Cancel H3, H4, H5 trouble |
| 16 |
|
Cancel U2 trouble |
| 21 |
1 |
Set maintenance cycle |
| 22 |
1 |
Check the print count value in each section and each operation mode |
| 2 |
Check the total number of misfeed and trouble |
| 3 |
Check misfeed ppositions and misfeed count of each position |
| 4 |
Check the trouble history |
| 5 |
Check the firmware version of each unit |
| 6 |
Output setting/adjustment data, firmware version and counter list |
| 8 |
Check the number of operation (counter value) of the finisher, SPF and scan (reading) unit |
| 9 |
Check the number of use (print counter) of each paper feed section |
| 10 |
Check the system configuration |
| 11 |
Check FAX counter |
| 12 |
Check SPF misfeed positions and number of misfeed at each position |
| 13 |
Check the operation time of the process section (Drum unit, DV unit, toner cartridge) and fusing unit |
| 14 |
Check the use status of the toner cartridge |
| 19 |
Check counter value of scan, image send mode |
| 23 |
2 |
Output JAM, trouble history data |
| 24 |
1 |
Clear JAM counter and trouble counter |
| 2 |
Clear paper feed counter of each paper feed section |
| 3 |
Clear SPF, scan (reading) and finisher counter |
| 4 |
Clear maintenance counter and print counter of the transport unit and the fusing unit |