PrintCopy.info service

Riso SF9490

 All About this machine
Table Of Contents 

Test Mode. List of Test Modes 0084 - 0103

No. Name Description Setting
0084 Test Print E (Dotl+Crossed Lines) Creates Test pattern 6 (Dot 1 + Crossed Lines).
The size of the crossed line pattern is 128 dots (5.4mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.042mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 8 dots (0.34mm) * 8 dots (0.34mm)
  • For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  • The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 -
0085 Test Print F (Dot2+Crossed Lines) Creates Test pattern 7 (Dot 2 + Crossed Lines).
The size of the crossed line pattern is 128 dots (10.8mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.084mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 16 dots (1.35mm) *
16 dots (0.68mm)
  • For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  • The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 -
0085 Test Print F (Dot2+Crossed Lines) Creates Test pattern 7 (Dot 2 + Crossed Lines).
The size of the crossed line pattern is 128 dots (5.4mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.042mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 16 dots (0.68mm) *
16 dots (0.68mm)
  • For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  • The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 -
0086 Test Print G (Dot3) Creates Test pattern 8 (Dot 3).
The dot pattern where the size of a black dot is 2 dots (0.169mm) * 2dots (0.084mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 -
0086 Test Print G (Dot3) Creates Test pattern 8 (Dot 3).
The dot pattern where the size of a black dot is 2 dots (0.084mm) * 2dots (0.084mm)
  • For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  • The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 -
0087 Paper Feed Test (Cycle) Performs the continuous printing action.
Speed 1: 60rpm, Speed 2: 80rpm, Speed 3: 100rpm, Speed 4: 120rpm, Speed 5: 130rpm, High Speed: 150rpm
  • The speed key is enabled.
  • The vertical print positioning key is enabled.
  • The action starts when the rear cover set switch is pressed. When the Start key is pressed, 10 seconds are waited until the rear cover set switch is pressed (A beep sounds until the set switch is pressed).
 -
0088 Low-speed Printing
Operation		 Performs the continuous printing action at 15rpm.
  • The conditions are the same as those of No.0087 (Paper Feed Test), except that the printing pressure and speed control is disabled.
  • The action starts when the rear cover set switch is pressed. When the Start key is pressed, 10 seconds are waited until the rear cover set switch is pressed (A beep sounds until the set switch is pressed).
 -
0090 Firmware Program
Download		 When the Start key is pressed, the machine firmware program is downloaded into the printer. -
0094 Unit Initialization Performs the mechanical initialization.
(scanner, TPH, master compression plate, clamp unit, vertical print position, and printing pressure)		 -
0095 System Configuration Data Output Creates a master for the CI system data and makes a print. -
0097 System Parameter, Error Record Print Creates a master of the list of data setting changes and error history and makes a print. -
0101 Clock Adjustment Confirm Applies the time set in Test Modes No.0171 - No.0173 to the RTC and starts the clock.
This test runs when the Start key is pressed and ends automatically after 0.5 second.
* This test must be run after values are set in Test Modes No.0171 - No.0173. This test
applies values set in Test Modes No.0171 - No.0173 to the RTC.		 -
0103 System-parameter adjustment store Stores information from the flash memory on MAIN-SYSTEM-PCB to the USB memory. -
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us