Riso ComColor 7010R

Entering Test Mode Numbers

Selection from Menus

With this method, test modes are narrowed down by choosing options in Category and Processing Category (S, M, U, I, C, or D) and the desired test mode is selected.

Entering Numbers Directly

With this method, the numeric keypad on the operation panel is used to enter the number when the printer is awaiting input of the test mode. To clear input errors, press the C button and enter the correct number.
Note: Leading zeros need not be entered. To enter 00100, you can simply enter 100.

Executing Test Modes

Sensor Monitoring (S)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen indicating the operation is paused. To cancel execution of test mode at this point, press the Stop key.

To continue with execution, press the Start key again. Next, the screen indicates that operation is either activated or deactivated.
When operation is activated, tones are emitted at short intervals.
When operation is deactivated, tones are emitted at long intervals.

To return to the test mode standby screen, press the Stop key on the operation panel.

Drive Checking (M)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen indicating the operation is paused. To cancel execution of test mode at this point, press the Stop key.

To continue with execution, press the Start key again. Next, the screen indicates that operation is in progress, and the particular unit is activated in isolation.

To return to the test mode standby screen, press the Stop key on the operation panel.

Unit Checking (U)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen indicating the operation is paused. To cancel execution of test mode at this point, press the Stop key.

To continue with execution (operation of multiple components), press the Start key again. Details regarding how operation is stopped are as follows.

• When the table indicates "Auto" for stopping operation, the screen displays "Finished" automatically after operation is finished.
• When the table indicates "Auto + Button" for stopping operation, pressing the Stop key stops operation, but processing will automatically end after the specified operation is finished.

When the table indicates "Button" for stopping operation, pressing the Stop key stops operation.

To return to the test mode standby screen, press the Stop key on the operation panel.

Initialization (I)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen indicating the operation is in progress. (The duration of display varies depending on the test mode, and the message is only displayed for an instant in some cases.) After the required processing is executed, "Finished" is displayed.

Processing is executed following details in the Confirmation Items column for initialization test modes.

To return to the test mode standby screen, press the Stop key on the operation panel.

Data Monitoring (C)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen with information.

To return to the test mode standby screen, press the Stop key on the operation panel.

Data Editing (D)

After you select or enter the test mode number in step 4-1, pressing the Start key on the operation panel will display a screen for numerical input, with the current setting value (selected value) in an orange row.

Changing Values

Enter values in the supported range directly, either by pressing the up or down arrow to increase or decrease the value or by entering the value with the numeric keypad.

Confirming Settings

To confirm the settings, press the OK button on the screen. To cancel any revisions, press Cancel.

Information on Bottom

min: Indicates the minimum value in the supported range for changes
max: Indicates the maximum value in the supported range for changes.
def: Indicates the factory-set default value.
step: Indicates the increment for changes. (For example, 2 indicates that the value is increased or decreased by 2.)

Notes: The units and meaning of values (and in particular, selection options) are not defined on the screen. Refer to the technical manual for details.

To return to the test mode standby screen, press the Stop key on the operation panel.