Riso CZ180
Test Mode. List. 5. Print-drum & Print-adjustment Test Modes 1
| No. | Sensors, switches | Detection status |
|---|---|---|
| 0800 | Position-A sensor | Blocked (detection plate detected) Drum is at position-B. |
| 0801 | Main motor FG sensor | Blocked (detection plate detected) |
| 0802 | Main-motor limit sensor | Blocked (encoder disc detected) |
| 0803 | Clamp sensor | Blocked (disc detected) |
| 0806 | Master loading sensor | Light reflected (master on the drum) |
| 0809 | Ink sensor | In contact with ink (ink present ) |
| 0810 | Overflow sensor | In contact with ink (ink present ) |
| 0811 | Ink bottle set switch | Switch pressed. |
| 0812 | Inking motor FG sensor | Blocked (encoder disc detected) |
| 0816 | Drum free rotation SW | Pressed |
| 0819 | Print-drum connection signal | Connected |
| 0820 | Print-drum safety switch | Switch ON (drum installed). Other safety switches must be ON for this check. |
| 0831 | Vertical-Centering Sensor | Blocked (detection plate present) |
| 0836 | Drum set sensor | Blocked (Drum installed) |
| No. | Motor solenoid system | Remarks |
|---|---|---|
| 0861 | Main-motor action (30 rpm) | Print drum rotation at speed of 30rpm. |
| 0863 | Clamp-motor action (Normal direction) | Clamp motor rotates in the normal (CCW) direction. |
| 0864 | Clamp-motor action (Opposite direction) | Clamp motor rotates in the opposite (CW) direction. |
| No. | Unit check |
|---|---|
| 0880 | Variable print-drum rotation Print speed key changes the drum rotation speed. |
| 0881 | Position-A action of the print drum Stops the print drum at position-A. |
| 0882 | Inking motor ON action Activates the inking motor for 10 seconds. |
| 0883 | Clamp home positioning action Resets the clamp unit to the home position. |
| 0884 | Clamp unit cycle action (3 step cycle) Make sure to bring the print drum to Position-A by test mode No. 0881 before activating this test mode to prevent machine damage. Press START key each time to perform the operations specified below. Step 1: From clamp plate closed position to clamp open. Step 2: From Clamp open position to Position-A compensation action. Step 3: From Position-A compensation action to clamp closed position. |
| 0886 | Clamp unit cycle action (3 step cycle) Make sure to bring the print drum to Position-A by test mode No. 0881 before activating this test mode to prevent machine damage. Press START key each time to perform the operations specified below. Step 1: From clamp plate closed position to clamp open. Step 2: From Clamp open position to Position-A compensation action. Step 3: From Position-A compensation action to clamp closed position. |
| 0886 | Pressure solenoid ON/OFF action. Press START key to switch ON the pressure solenoid. The solenoid switches OFF automatically 10 seconds later. |
| 0887 | Print drum inking action Performs the inking operations in following sequence by one press of the START key: 1. Pumps in the ink into print drum while rotating the drum until the Ink Sensor detects Ink, without pressure roller touching the print drum. 2. Makes a confidential master on the print drum. 3. From the time the ink sensor detects the ink again, the print drum makes 10 rotations with the Pressure Roller pressing against the print drum. 4. The print drum stops at Position-B. |
| 0888 | Print drum ink-drainage action. Performs the ink drainage from the print drum in following sequence by one press of the START key: 1. Makes TPH test mode image on the master and wraps around the print drum. 2. Printing is started with no inking motion and with the ink sensor deactivated. 3. The printing is continued until the STOP key is pressed. 4. The print drum stops at Position-B. |
| 0892 | Machine Position-B stop. (The position in which the print drum can be removed from the machine.) Stops the print drum at machine Position-B. (The test mode can be activated with or without print drum in the machine.) |
| 0900 | Vertical-centering action Moves the vertical print position to the home (center) position. |
| 0901 | Vertical print position one cycle action. Makes one cycle vertical print positioning movement. (Maximum to each way and back to home position) |
| No. | Data check | Details |
|---|---|---|
| 0921 | Print-drum angle display | Displays the present print-drum angle. (example: 1800 = 180°) |
| 0923 | Print-drum ink temperature display | Displays the temperature of the ink in the print drum in degrees Celsius [° C]. |
| 0925 | Ink remaining volume display | Displays the amount of ink left in the ink bottle in percentage (%) [Ink TAG information] |
| 0926 | Inking motor FG count (Displays 10,000th count number) | Displays the inking motor FG count value read from the ink bottle tag. (1 count = 0.1 ml) Example: For the 12,648 FG count, [ 9 ] is displayed. |
| 0927 | Inking motor FG count (Displays up to 1,000th count number) | Displays the inking motor FG count value read from the ink bottle tag. (1 count = 0.1 ml) Example: For the 12,648 FG count, [ 2648 ] is displayed. |