Riso CV1860
Test Mode. List. 3. Master-making & Master-disposal Test Modes 2
| No. | Data check | Details |
|---|---|---|
| 0521 | TPH thermistor temperature data | Displays the temperature of the TPH thermistor in [degrees Celsius] |
| 0524 | TPH power voltage | Displays the voltage applied to the TPH when the power to the TPH is switched ON. (The display is voltage x 100. Example: 10V=1000.) |
| No. | Data setting | |
|---|---|---|
| 0540 | Master Leading-Edge Position Adjust | |
| Description | Adjusts return amount of the master material from the Master positioning sensor after the master is set or master cutting operation is made. The pulse is counted from the time the Master positioning sensor no longer detect the master leading edge. | |
| Setting | Range : 0 to 100 (0mm to +10.0mm) (+ value returns the master material further back from the sensor) Unit : 1 (0.1mm) Default : 50 (5.0mm) |
|
| 0541 | Write start-position adjustment | |
| Description | Adjusts the master-making start position on the master material by changing the rotation amount of the Write pulse motor in CW or CCW direction before the write-signal goes on. (This adjustment does not affect the master-clamp-amount.) | |
| Setting | Range : -50 to +50 (-5.0mm to +5.0mm) (+ values return the master material back more before the write signal goes on. The master-making starts from closesr to the leading edge of the master material. As a result, the printed image position on the paper comes up.) Unit : 1 (0.1mm) Default : -5 (-0.5mm) |
|
| 0542 | Master-making length adjustment | |
| Description | Adjusts the master-making area length. | |
| Setting | Range : -100 to +100 (-10.0mm to +10.0mm) (+ values increase master-making area length) Unit : 1 (0.1mm) Default : 0 (0mm) |
|
| 0543 | Master-clamp-amount adjustment | |
| Description | Adjusts the master-clamp amount under the clamp plate during master loading onto the drum. (This adjustment affects the master-write-start-position) | |
| Setting | Range : -100 to +100 (-10.0mm to +10.0mm) (+ values increase clamping amount) Unit : 1 (0.1mm) Default : 10 (1.0mm) |
|
| 0544 | Master cut length adjustment | |
| Description | Adjusts the total length of one master (changes the master cut timing against the drum angle). | |
| Setting | Range : -200 to +200 (-20.0mm to +20.0mm) (+ values increase the master length). Unit : 1 (0.1 mm) Default : -35 (-3.5mm) |
|
| 0547 | Master-making speed adjustment (Image elongation & shrinkage) | |
| Description | Image elongation and shrinkage in making master. (Adjusts the speed of the write pulse motor.) | |
| Setting | Range : -100 to +100 (-10.0% to +10.0%) ( + values elongate the image in master making.). Unit : 1 (0.1%) Default : -5 (-0.5%) |
|
| 0552 | Thermal Print Head (TPH) over-heat temperature | |
| Description | Sets the temperature reference parameter to judge TPH over-heat. If the machine detects the TPH temperature to be above this parameter, the machine displays a message and stops the master-making job. Turning the machine power OFF and then ON will reset the error message. | |
| Setting | Range : 0 to 255 (0 degrees Celcius to 255 degrees Celcius) (Master compression plate 65° to 100° from HP position). Unit : 1 (1 degrees Celcius) Default : 45 (45 degrees Celcius) |
|
| 0553 | Thermal Print Head (TPH) over-heat temperature detection Enable or Disable selection. | |
| Description | Selection of enabling or disabling the TPH over-heat detection by Test Mode No.0552. | |
| Setting | Range : 0 or 1 0 = Disable 1=Enable Default : 1 (Enable) |
|
| 0554 | Master return amout after cutter blade disc cuts the master and stops at the cutter-stop-position. | |
| Description | Sets the master return amout after cutter cuts the master and stops at the cutter-stop-position, before the cutter returns to the HP position. (This is to prevent the leading edge of the master from jamming on the cutter blade disc when the blade returns to the HP position.) | |
| Setting | Range : -36 to +36 (-3.6mm to +3.6mm) (+ value returns the master material away from the cutter unit in addition to the standard return amount programmed.) Unit : 1 (0.1mm) Default : 0 (0mm) |
|
| 0578 | Master removal motor speed selection | |
| Description | Selects the master-disposal-motor speed in relation to the print drum rotation speed. | |
| Setting | Range : 0 to 2 0: Same speed as the print drum speed. 1: 10% faster than the print drum speed. (default) 2: 20% faster than the print drum speed. |
|
| 0585 | Master disposal box FULL software count Enable or Disable selection. | |
| Description | Selection of enabling or disabling the software count FULL detection. | |
| Setting | Range : 0 or 1 0 = Disable 1=Enable Default : 1 (Enable) |
|