Ricoh MP5002SP
Service Program Mode Tables. SP11XX: FEED
1103* | ||
---|---|---|
Fusing Idling | ||
Switches fusing idling on/off. When on, printing will not start until enough time has elapsed so the hot roller can reach optimum temperature. This ensures even heat on the hot roller. Switch on if fusing on the 1st and 2nd copies is incomplete (this may occur if the room is cold.). You must switch SP1103-1 ON before you set the fusing interval with SP1103-2. | ||
001 | Enable Fusing Idling | 0 = Off, 1 = On |
002 | Interval | [0 to 60 / 30 / 1 sec.] |
003 | Idling Time at Every Job | Sets the machine to fusing idling only for 30 sec. for every job (when the original is set on the ARDF, when the ARDF cover is opened, etc.) and the fusing unit has reached the reload temperature (optimum temperature for operation). [0 to 30 / 0 / 1 sec.] 0: No idling done before a job. |
1104* | ||
Fusing Temperature Control | ||
On-Off/Phase | ||
Selects the fusing temperature control method. After changing this setting, be sure to turn the machine off and on again with the main power switch to enable the new setting. [0 to 1 / 0 / 1] • 0: Normal (ON/OFF control). Allows full application from ac power supply to bring the hot roller up to the target fusing temperature then shuts off. Determines the on-time from the present temperature (detected by the thermistor on the hot roller) and the temperature of 1 cycle before. • 1: Phase (hysterisis) control. Sets the upper and lower limits for the temperature; at the lower temperature the fusing lamp is on and at the higher temperature the fusing lamp is off. Change this setting to "0" only if the user has excessive electrical noise or interference on the power supply line. Such interference can cause voltage to drop when power is applied using the ON/OFF control method. Interference can be caused by the general poor quality of the power supply lines, or if the machine is sharing a power supply with other electrical devices such as fluorescent lights. Before changing this setting, make sure that the machine is connected to a power supply not shared by other electrical equipment. ◦ Selecting Phase control ("1") could cause the fusing temperature control board to emit low pitched noise |
||
1105* | ||
Fusing Temperature Adjustment | ||
Allows adjustment of the hot roller temperature at the center and ends of the roller for the quality or thickness of the paper. The hot roller in this machine has two fusing lamps: one heats the center of the roller, the other heats both ends. Each fusing lamp can be adjusted separately. The "re-load temperature" is the "print ready temperature". When the fusing temperature exceeds this setting, the machine can operate. Do not set up a re-load temperature (Re-load Temp. = Fusing. Temp – SP Value.) that is higher than the SP1-105-2 setting. | ||
001 | Roller Center Adjusts the fusing temperature at the center of the hot roller. |
C1b/C1.5b: [100 to 170 / 140 / 1 deg] C1c/C1.5c: [100 to 170 / 150 / 1 deg] |
002 | Roller Ends Adjusts the fusing temperature at the ends of the hot roller. |
C1b/C1.5b: [100 to 170 / 145 / 1 deg] C1c/C1.5c: [100 to 170 / 155 / 1 deg] |
003 | Re-load Temp. Minus: Roller Center Sets the reload temperature for the center of the hot roller. This setting depends on the target temperature. Reload temp. = Target Temp – This SP Setting ▪ Do not set a temperature that is higher than the setting for SP1105 1 (Roller Center: Trays) |
[0 to 60 / 0 / 1 deg] |
004 | Re-load Temp. Minus: Roller Ends Sets the reload temperature for the ends of the hot roller. This setting depends on the target temperature. Reload temp. = Target Temp – This SP Setting ▪ Do not set a temperature that is higher than the setting for SP1105 2 (Roller Ends: Trays) |
[0 to 60 / 0 / 1 deg] |
005 | Roller Center: M-Thick | C1b/C1.5b: [100 to 170 / 145 / 1 deg] C1c/C1.5c: [100 to 170 / 155 / 1 deg] |
006 | Roller Ends: M-Thick | C1b/C1.5b: [100 to 170 / 150 / 1 deg] C1c/C1.5c: [100 to 170 / 160 / 1 deg] |
007 | Roller Center: Thick 1 | [100 to 170 / 130 / 1 deg] |
008 | Roller Ends: Thick 1 | |
009 | Roller Center: Thick 2 | [100 to 170 / 150/ 1 deg] |
010 | Roller Ends: Thick 2 | |
011 | Roller Center: Thin | C1b/C1.5b: [100 to 170 / 130 / 1 deg] C1c/C1.5c: [100 to 170 / 140 / 1 deg] |
012 | Roller Ends: Thin | C1b/C1.5b: [100 to 170 / 135 / 1 deg] C1c/C1.5c: [100 to 170 / 145 / 1 deg] |
013 | Roller Center: OHP: Plain | [100 to 170 / 150/ 1 deg] |
014 | Roller Ends: OHP: Plain | [100 to 170 / 155/ 1 deg] |
015 | Roller Center: OHP: Thick | |
016 | Roller Ends: OHP: Thick | [100 to 170 / 160/ 1 deg] |
017 | Roller Center: Special 1 | C1b/C1.5b: [100 to 170 / 140 / 1 deg] C1c/C1.5c: [100 to 170 / 150 / 1 deg] |
018 | Roller Ends: Special 1 | C1b/C1.5b: [100 to 170 / 145 / 1 deg] C1c/C1.5c: [100 to 170 / 155 / 1 deg] |
019 | Roller Center: Special 2 | C1b/C1.5b: [100 to 170 / 140 / 1 deg] C1c/C1.5c: [100 to 170 / 150 / 1 deg] |
020 | Roller Ends: Special 2 | C1b/C1.5b: [100 to 170 / 145 / 1 deg] C1c/C1.5c: [100 to 170 / 155 / 1 deg] |
021 | Roller Center: Special 3 | C1b/C1.5b: [100 to 170 / 140 / 1 deg] C1c/C1.5c: [100 to 170 / 150 / 1 deg] |
022 | Roller Ends: Special 3 | C1b/C1.5b: [100 to 170 / 145 / 1 deg] C1c/C1.5c: [100 to 170 / 155 / 1 deg] |
023 | Feed Waiting: Plain | Turns the feed waiting mode on or off for each paper type. [0 to 1 / 0 / 1] 0=Off, 1=On The paper waits at the registration roller until the fusing temperature reaches the prescribed temperature (adjustable with SP1105-028 to -37). If you enable this feature, also set SP 1105-38 to a convenient value for the customer. |
024 | Feed Waiting: M-Thick | |
025 | Feed Waiting: Thick 1 | |
026 | Feed Waiting: Thick 2 | |
027 | Feed Waiting: Thin | |
028 | Feed Wait: Center Minus: Plain | Adjusts the offset value for each re-load temperature to exit the feed waiting mode. [0 to 60 / 0 / 1 deg] |
029 | Feed Wait: Ends Minus: Plain | |
030 | Feed Wait: Center Minus: M-Thick | |
031 | Feed Wait: Ends Minus: M-Thick | |
032 | Feed Wait: Center Minus: Thick 1 | |
033 | Feed Wait: Ends Minus: Thick 1 | |
034 | Feed Wait: Center Minus: Thick 2 | |
035 | Feed Wait: Ends Minus: Thick 2 | |
036 | Feed Wait: Center Minus: Thin | |
037 | Feed Wait: Ends Minus: Thin | |
038 | Feed Waiting: Maximum Time | Sets the maximum feed waiting time. [0 to 30 / 0 / 1 sec] The paper is fed when the time specified with this SP has passed even though the fusing temperature has not reached the prescribed temperature. 0: Disabled. |
1106 | ||
Fusing Temperature Display | ||
001 | Roller Center | Displays the temperature of the fusing unit. [-20 to 250 / 0 / 1 deg] |
002 | Roller Ends | |
003 | Machine Inside at Power On | Displays the temperature inside the machine. [-20 to 250 / 0 / 1 deg] |
004 | Machine Inside | |
1109* | ||
Fusing Nip Band Check | ||
Checks the fusing nip band. | ||
001 | Execution | |
002 | Idling Rotation Time Specifies the fusing rotation time before executing SP1109-001. |
[0 to 120 / 60 / 1 sec] |
003 | Pre-Idling Time Specifies the time that the paper stops in the fusing unit for measuring the nip. |
[5 to 30 / 10 / 1 sec] |
1159 | ||
Fusing Jam Detection | ||
SC Code Display | ||
[0 to 1 / 0 / 1] 0:OFF, 1:ON This SP setting determines whether SC559 is issued after three paper late jams occur in the fusing unit. After this SP code is turned on, a counter monitors the number of paper late jams that occur in the fusing unit. After the 3rd occurrence of a fusing jam, SC559 is issued and the machine cannot be used until the service technician releases the error. • Switching the machine off/on does not reset this jam counter. The counter is reset after the cause of the jam has been removed and a sheet of paper successfully passes the fusing exit sensor. |