Ricoh D250 MP3054SP Cor-C1
Adjustment. Printing. Registration - Leading Edge/Side-to-Side
These adjustments must be performed after replacing any of the following parts:
• Scanner wires
• Lens block
• Scanner motor
• Polygon motor
• Tandem tray side fences
• Memory All Clear
Preparation
- Make sure paper is installed correctly in each paper tray before you start these adjustments.
- Use the Trimming Area Pattern (SP2-902-3, No. 18 to print the test pattern for the following procedures.
- After completing these printing adjustments, be sure to set SP 2-902-3 to 0 again.
Procedure
- Check the leading edge registration, and adjust it using SP1-001. Specification: 4±2mm.
- Check side-to-side registration for each paper feed station, and adjust with the following SP modes.
A: Leading Edge Registration (4.2 ± 1.5 mm)
B: Side-to-side Registration (2 ± 1.5 mm)
1. Check the leading edge registration [A] for each paper feed station, and adjust them using SP1-001.
Threshold: 4.2 ± 1.5 mm
| Tray | SP No. |
|---|---|
| Tray1: Thin | SP1-001-001 |
| Tray1: Plain | SP1-001-002 |
| Tray1: MidThick | SP1-001-003 |
| Tray1: Thick1 | SP1-001-004 |
| Tray1: Thick2 | SP1-001-005 |
| Tray1: Thick3 | SP1-001-006 |
| Tray1: Thick4 | SP1-001-007 |
| Tray2: Thin | SP1-001-008 |
| Tray2: Plain | SP1-001-009 |
| Tray2: MidThick | SP1-001-010 |
| Tray2: Thick1 | SP1-001-011 |
| Tray2: Thick2 | SP1-001-012 |
| Tray2: Thick3 | SP1-001-013 |
| Tray2: Thick4 | SP1-001-014 |
| Bypass: Thin | SP1-001-015 |
| Bypass: Plain | SP1-001-016 |
| Bypass: MidThick | SP1-001-017 |
| Bypass: Thick1 | SP1-001-018 |
| Bypass: Thick2 | SP1-001-019 |
| Bypass: Thick3 | SP1-001-020 |
| Bypass: Thick4 | SP1-001-021 |
| Duplex: Thin | SP1-001-022 |
| Duplex: Plain | SP1-001-023 |
| Duplex: MidThick | SP1-001-024 |
| Duplex: Thick1 | SP1-001-025 |
| Duplex: Thick2 | SP1-001-026 |
| Duplex: Thick3 | SP1-001-027 |
| Tray1: Thin: 1200 | SP1-001-028 |
| Tray1: Plain: 1200 | SP1-001-029 |
| Tray1: MidThick: 1200 | SP1-001-030 |
| Tray1: Thick1: 1200 | SP1-001-031 |
| Tray1: Thick2: 1200 | SP1-001-032 |
| Tray1: Thick3: 1200 | SP1-001-033 |
| Tray1: Thick4: 1200 | SP1-001-034 |
| Tray2: Thin: 1200 | SP1-001-035 |
| Tray2: Plain: 1200 | SP1-001-036 |
| Tray2: MidThick: 1200 | SP1-001-037 |
| Tray2: Thick1: 1200 | SP1-001-038 |
| Tray2: Thick2: 1200 | SP1-001-039 |
| Tray2: Thick3: 1200 | SP1-001-040 |
| Tray2: Thick4: 1200 | SP1-001-041 |
| Bypass: Thin: 1200 | SP1-001-042 |
| Bypass: Plain: 1200 | SP1-001-043 |
| Bypass: MidThick: 1200 | SP1-001-044 |
| Bypass: Thick1: 1200 | SP1-001-045 |
| Bypass: Thick2: 1200 | SP1-001-046 |
| Bypass: Thick3: 1200 | SP1-001-047 |
| Bypass: Thick4: 1200 | SP1-001-048 |
| Duplex: Thin: 1200 | SP1-001-049 |
| Duplex: Plain: 1200 | SP1-001-050 |
| Duplex: MidThick: 1200 | SP1-001-051 |
| Duplex: Thick1: 1200 | SP1-001-052 |
| Duplex: Thick2: 1200 | SP1-001-053 |
| Duplex: Thick3: 1200 | SP1-001-054 |
2. Check the side-to-side registration [B] for each paper feed station, and adjust them using SP1-002.
Threshold: 2 ±1.5 mm
| Tray | SP No. |
|---|---|
| Tray 1 | SP1-002-002 |
| Tray 2 | SP1-002-003 |
| Tray 3 (Optional PFU tray 1 or LCT) | SP1-002-004 |
| Tray 4 (Optional PFU tray 2) | SP1-002-005 |
| Duplex (side 1) | SP1-002-006 |
| LCT | SP1-002-007 |