Ricoh D130-17 MP5002
Service Program Mode Tables. SP19XX: FEED
| 1902 | ||
|---|---|---|
| Cleaning Web Setting | ||
| 001 | Web Consumption Displays the consumed amount of the web roll. |
[0 to 120 / 0 / 1 %] |
| 002 | Web Motor Interval Adjusts the interval for web motor rotation. |
C1b/C1.5b: [3 to 130 / 8.4 / 0.1 sec] C1c/C1.5c: [3 to 130 / 6.7 / 0.1 sec] |
| 003 | Web Motor Time Adjusts the rotation time of the web motor. |
[0.3 to 10 / 4.2 / 0.1 sec] |
| 004 | Web Near End Setting Adjusts the threshold for web near end. |
C1b/C1.5b: EU [0 to 100 / 90 / 1 %] C1b/C1.5b: ASIA/NA [0 to 100 / 92 / 1 %] C1c/C1.5c: EU [0 to 100 / 90 / 1 %] C1c/C1.5c: ASIA/NA [0 to 100 / 92 / 1 %] |
| 005 | Web Motor Interval: Thick 1 Adjusts the interval for web motor rotation (thick 1). |
[3 to 130 / 11.2 / 0.1 sec] |
| 006 | Web Motor Interval: Thick 2 Adjusts the interval for web motor rotation (thick 2). |
[3 to 130 / 16.8 / 0.1 sec] |
| 007 | Paper Interval Time Adjusts the threshold for paper feeding. When the time between trailing edge detection and leading edge detection is within the value of this setting, the machine determines that the paper is still being fed. |
[0 to 10 / 5 / 1 sec] |
| 008 | Web Motor Setting: Web End Adjusts the motor rotation time after the web end. |
[0 to 60 / 27 / 1 sec] |
| 009 | Web Motor Rotation: Power On Adjusts the number of web motor rotations at the re-load state. |
[0 to 10 / 2 / 1 times] |
| 010 | Web Motor Interval: Pre-idle Adjusts the motor waiting time after the fusing motor idling. |
[0 to 30 / 5 / 1 sec] |
| 011 | Web Motor Rotation: Pre-idle Adjusts the number of web motor rotations at the fusing idling state. |
[0 to 10 / 2 / 1 times] |
| 1903 | ||
|---|---|---|
| Cleaning Web Setting | ||
| 001 | Total Paper Counter Displays the total paper feeding time. |
[0 to 999999999 / 0 / 1 sec] |
| 002 | Total Web Motor Drive Time Displays the total time of web motor rotation. |
[0 to 999999999 / 0 / 1 sec] |
| 1907 | ||
|---|---|---|
| Paper Feed Timing Adj. (DFU) | ||
| 001 | Feed Solenoid ON: Plain | [-10 to 40 / 0 / 2.5 mm] |
| 002 | Feed Solenoid ON: Thick | |
| 003 | Feed Solenoid OFF: Plain | [-10 to 10 / 0 / 1 mm] |
| 004 | Feed Solenoid OFF: Thick | |
| 005 | Feed Clutch ON: Plain | |
| 006 | Feed Clutch ON: Thick | |
| 007 | Stop Position before Inverter | |
| 008 | Stop Position after Inverter | |
| 009 | Re-Feed Stop Position | |
| 010 | By-pass Solenoid OFF | [0 to 40 / 0 / 1 mm] |
| 011 | By-pass Solenoid ON | [0 to 1 / 1 / 1 mm] |
| 012 | By-pass Feed Clutch ON | [-10 to 10 / 0 / 1 mm] |
| 013 | Exit Roller: Shift: 180 | |
| 014 | Exit Roller: Shift: 230 | |
| 015 | Exit: Junction Solenoid ON | |
| 016 | Exit: Junction Solenoid OFF | |
| 017 | Bridge: Junction Solenoid ON | |
| 018 | Bridge: Junction Solenoid OFF | |
| 019 | 1-Bin: Junction Solenoid ON | |
| 020 | 1-Bin: Junction Solenoid OFF | |
| 021 | Shift Motor ON | [-1 to 1 / 0 / 0.1 mm] |
| 1908 | ||
|---|---|---|
| Paper Bank Feed Timing Adj (DFU) | ||
| 001 | Feed Clutch ON: Plain | [-10 to 10 / 0 / 1 mm] |
| 002 | Feed Clutch ON: Thick | |
| 1916 | ||
|---|---|---|
| CPM Down Setting | ||
| When this machine gets a sequence of coping/printing jobs, the machine uses CPM down mode to prevent the fusing temperature from becoming too low. | ||
| 001 | Temp.: Plain | Adjusts the thresholds for each environmental condition (between Low and Medium). [10 to 23 / 17 / 1 deg] |
| 002 | Temp.: M-Thick | |
| 003 | Temp.: Thick 1 | |
| 004 | Temp.: Thick 2 | |
| 005 | Temp.: Thin | |
| 006 | ON/OFF: Low: Plain | Turns on or off the CPM down setting for each paper type and ambient temperature. [0 to 1 / 0 / 1 ] 0= Off, 1= On |
| 007 | ON/OFF: Low: M-Thick | |
| 008 | ON/OFF: Low: Thick 1 | |
| 009 | ON/OFF: Low: Thick 2 | |
| 010 | ON/OFF: Low: Thin | |
| 011 | ON/OFF: Medium: Plain | |
| 012 | ON/OFF: Medium: M-Thick | |
| 013 | ON/OFF: Medium:: Thick 1 | |
| 014 | ON/OFF: Medium: Thick 2 | |
| 015 | ON/OFF: Medium: Thin | |
| 016 | Waiting Time: Low: Plain | Adjusts the threshold time to enter the CPM down mode. [0 to 180 / 60 / 1 sec] The machine determines whether the CPM down mode is activated or not after the time specified with these SPs has passed. |
| 017 | Waiting Time: Low: M-Thick | |
| 018 | Waiting Time: Low: Thick 1 | |
| 019 | Waiting Time: Low: Thick 2 | |
| 020 | Waiting Time: Low: Thin | |
| 021 | Waiting Time: Medium: Plain | |
| 022 | Waiting Time: Medium: M-Thick | |
| 023 | Waiting Time: Medium: Thick 1 | |
| 024 | Waiting Time: Medium: Thick 2 | |
| 025 | Waiting Time: Medium: Thin | |
| 026 | Temp.: Low: Plain | Adjusts the threshold temperature of the fusing unit to enter the CPM down mode. [100 to 200 / 120 / 1 deg] If the temperature of the fusing unit is less than the temperature specified with these SPs, the machine changes the CPM (adjustable with SP1916-36 to -45). |
| 027 | Temp.: Low: Plain | |
| 028 | Temp.: Low: Thick 1 | |
| 029 | Temp.: Low: Thick 2 | |
| 030 | Temp.: Low: Thin | |
| 031 | Temp.: Medium: Plain | |
| 032 | Temp.: Medium: M-Thick | |
| 033 | Temp.: Medium: Thick 1 | |
| 034 | Temp.: Medium: Thick 2 | |
| 035 | Temp.: Medium: Thin | |
| 036 | CPM: Low: Plain | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [20 to 35 / 35 / 5 cpm] C1c/C1.5c: [20 to 45 / 45 / 5 cpm] |
| 037 | CPM: Low: M-Thick | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [20 to 35 / 35 / 5 cpm] C1c/C1.5c: [20 to 45 / 45 / 5 cpm] |
| 038 | CPM: Low: Thick 1 | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [5 to 15 / 15 / 5 cpm] C1c/C1.5c: [5 to 25 / 25 / 5 cpm] |
| 039 | CPM: Low: Thick 2 | Adjusts the CPM in the CPM down mode. [5 to 15 / 15 / 5 cpm] |
| 040 | CPM: Low: Thin | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [20 to 35 / 35 / 5 cpm] C1c/C1.5c: [30 to 45 / 45 / 5 cpm] |
| 041 | CPM: Medium: Plain | |
| 042 | CPM: Medium: M-Thick | |
| 043 | CPM: Medium: Thick 1 | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [5 to 15 / 15 / 5 cpm] C1c/C1.5c: [5 to 25 / 25 / 5 cpm] |
| 044 | CPM: Medium: Thick 2 | Adjusts the CPM in the CPM down mode. [5 to 15 / 15 / 5 cpm] |
| 045 | CPM: Medium: Thin | Adjusts the CPM in the CPM down mode. C1b/C1.5b: [20 to 35 / 35 / 5 cpm] C1c/C1.5c: [30 to 45 / 45 / 5 cpm] |
| 1930 | ||
|---|---|---|
| OnOff Time Adjust | ||
| 001 | On Time Adjus Adjusts the Off-On interval of the transfer belt contact motor. ("On" means that the transfer belt is in contact with the drum.) t |
[0 to 100 / 40 / 10 msec] |
| 002 | Off Time Adjust Adjusts the On-Off interval of the transfer belt contact motor. ("Off" means that the transfer belt is away from the drum.) |
[0 to 100 / 20 / 10 msec] |