Ricoh D130-17 MP5002
Maintenance. PM TABLES. MAINFRAME
Amounts mentioned as the PM interval indicate the number of prints.
Symbol key: C: Clean, R: Replace, L: Lubricate, I: Inspect
| EM | 160K | 320K | 800K | Note | |
|---|---|---|---|---|---|
| Scanner/Optics | |||||
| Reflector | C | Optics cloth | |||
| 1st Mirror | C | Optics cloth | |||
| 2nd Mirror | C | Optics cloth | |||
| 3rd Mirror | C | Optics cloth | |||
| Scanner Guide Rails | C | Do not use alcohol. | |||
| Exposure Glass | C | C | Cleaner | ||
| Toner Shield Glass | C | C | Dry cloth or cleaner | ||
| APS Sensor | C | Dry cloth | |||
| Exposure Glass (Sheet through) | C | C | Cleaner | ||
| LED Board | C | ||||
| Drum (OPC) Area | |||||
| OPC Drum | I | R | |||
| Charge Roller | R | ||||
| Charge Roller Cleaning Roller | R | ||||
| Drum Cleaning Blade 1 | R | ||||
| Quenching Lamp | C | Dry cloth | |||
| Pick-off Pawls | R | ||||
| Spurs | C | C | Dry cloth | ||
| ID Sensor | C | C | Perform SP3-001-2 after blower brush cleaning. | ||
| Cleaning Entrance Seal | C | Blower brush. Replace if required. | |||
| Side Seal | C | ||||
| Development Unit | |||||
| Development Drive Gears | C | Dry cloth | |||
| Development Filter | R | ||||
| Developer | I | R | |||
| Entrance Seal | C | C | |||
| Side Seal | I | ||||
| Development Roller | C | Dry cloth | |||
| Development Case | C | C | |||
| Development Sleeve | C | ||||
| Lock Lever | C | C | |||
| Paper Feed | |||||
| Registration Roller | I | C | Water | ||
| Idle Roller Dust Blade | I | C | Detach and tap gently on flat surface to empty. Blower brush. | ||
| Registration Roller Dust Blade | I | C | Blower brush. | ||
| Feed Rollers | I | C | Water | ||
| Pick-up Rollers | I | C | Water | ||
| Separation Rollers | I | C | Water | ||
| By-pass Feed Roller | I | C | Water | ||
| By-pass Pick-up Roller | I | C | Water | ||
| By-pass Separation Roller | I | C | Water | ||
| Paper Feed Guides | I | C | Dry cloth | ||
| Relay Rollers | I | C | Water | ||
| Bottom Plate Pad | I | C | Water | ||
| Bottom Plate Pad (By-pass feed) | I | C | Water | ||
| Registration Sensor | I | C | Blower brush | ||
| By-pass Feed Roller Gear | I | L | Silicone Grease G-501 | ||
| Relay Sensors | I | C | Blower Brush | ||
| Paper Feed Sensors | I | C | Blower Brush | ||
| Duplex Unit | |||||
| Inverter Rollers | I | C | Water | ||
| Transport Rollers | I | C | Water | ||
| Entrance Sensor | I | C | Water | ||
| Exit Sensor | I | C | Water | ||
| Transfer Belt Unit | |||||
| Transfer Belt | C | R | Dry cloth. To prevent damage to the cleaning blade, always replace these items together. | ||
| Transfer Belt Cleaning Blade | R | ||||
| Transfer Belt Rollers | C | Dry cloth | |||
| Transfer Entrance Guide | C | C | Dry cloth | ||
| Entrance Seal | C | Dry cloth | |||
| Used Toner Tank | I | C | Empty the tank | ||
| Seal (for paper dust) | C | ||||
| Paper Exit | |||||
| Paper Exit Sensor | I | I | Blower brush | ||
| Junction Gate Jam sensor | I | C | Blower brush | ||
| Fusing Exit Sensor | I | I | Blower brush | ||
| Paper Exit Rollers | I | I | Water | ||
| Junction Transport Roller | I | I | Water | ||
| Paper Exit Guide | I | I | Water | ||
• Due to their durability and extended service life, the feed rollers, separation rollers, and pick-up rollers of the mainframe, optional paper trays, and LCT are not replaced at PM.