Ricoh D0BW IM600SRF

Overview

In order to update the firmware of this machine, download the latest firmware file and save on an SD card. Once saved, insert the SD card in the SD Card Slot 2.

Firmware Types

Firmware Location	Firmware Type	Message Displayed
Controller Board (PCB15)	System/Copy	BRZP2a_system
	NetworkDocBox	BRP2a_netfile
	Network Support	BRZP2a_net
	Printer	BRZP2e_printer
	PCL	BRP2e_prt_PCL
	PDF (IRIPS PDF)	BRP2e_prt_IPDF
	PS (IRIPS PS)	BRP2e_prt_IPS3
	Web Support	BRZP2a_web
	RPCS	BRP2e_prt_RPCS
	FONT(Font EXP)	GW14e_prt_SAMf
	MediaPrint:TIFF	BRZP2e_printer
	HDD Format Option	GW2a_zoffyxonb
	PowerSaving Sys	BRZP2e_subcpu
IOB (PCB17)	Engine	BRP2a_eplot
BiCU (PCB16)	Engine(IPU)	BRP2a_eipu

• Even when not using an RPCS driver, the XPS driver requires RPCS firmware.

Procedure

• An SD card is a precision device, so when you handle an SD card, respect the following.
• When the power is switched ON, do not insert or remove a card.
• During installation, do not switch the power OFF.
• Since the card is manufactured to high precision, do not store it in a hot or humid location, or in direct sunlight.
• Do not bend the card, scratch it, or give it a strong shock.
• Before downloading a firmware file on an SD card, check if the write-protection of the card is disabled or not. If write-protection is enabled, an error code (error code 44, etc.) will be displayed during download, and the download will fail.
• Before updating the firmware, disconnect the network cable from the machine.
• If SC818 is generated during the software update, switch the power OFF -> ON, and complete the update which was interrupted.
• During software update, remove interface cables, network cables, wireless boards, etc., (so that they are not accessed during the update).

1. First, download the software to be updated to the SD card.
2. Turn OFF the main power.
3. Remove the controller cover. (Controller Cover)
   Insert the SD card [A] straight in the SD Card Slot 2 (lower).
   

   • If the customer has used all of the slots, you have to keep an empty slot for this procedure. Ask the customer to temporarily remove the SD card in SD Card Slot 2.
   • Check whether the card is properly in the SD Card Slot. When an SD card is inserted, a click is heard, and it is locked.
   • To remove the card, release by pressing once in the set state.

4. Turn ON the main power.
5. Wait until a firmware name is shown on the display (about 1 minute).
   • The firmware name is read from inside the firmware. The firmware name is not changed even if you change the file name on your PC.
6. If the necessary firmware name is shown on the display, check the firmware version with the leftarrow or right-arrow keys. Pressing the left or right-arrow key shows the firmware name, version, and serial number in order.
7. To use a different firmware file, push the up-arrow key or the down-arrow key to find the necessary file.
8. To select the firmware, push the OK key. Make sure that the selected firmware is highlighted.
9. If you update more than one firmware program at the same time, find each of them and select each of them. Make sure that the selected firmware is highlighted.
10. To start the firmware update, push the "UpDate" key. While each firmware is downloaded, the underscores on the operation panel are replaced by stars.
11. 11. Wait until the message "Update done" is shown.
12. After turning OFF the main power, remove the SD card.
13. Again, turn ON the main power, and check whether the machine is operating normally.
14. Print the Configuration Page to check that the firmware is correctly updated: List/Test Print > Config. Page
15. Reassemble the machine.
    • An error code is shown if an error occurs during the download. Error codes have the letter "E" and a number. If an error occurs, the firmware is not correctly downloaded; see the error code table (Error Screens During Updating) and do the necessary steps. After this, download the firmware again.
    • If the firmware update is interrupted by a power failure, the firmware is not correctly downloaded. In this condition, machine operation is not guaranteed. You have to download the firmware again.