OKI MC363

Jam occurs immediately after the power is turned on.

Check item	Checking method	Action
Check condition of the paper running path
Paper running path of the front unit	Open the front cover check if paper is not jammed in the paper running path.	Remove the jammed paper.
Check condition of the mechanical parts
Hopping sensor, IN sensor and WR sensor lever check	Check the sensor lever shapes and operations for any problem.	Replace the sensor lever(s) with proper one(s).
Check condition of electrical parts
Check the detection condition of the sensor signal	Confirm that the sensor signals are normally detected by using the Maintenance Menu SWITCH SCAN function	Replace the CU/PU board or sensor or cable.
Hopping sensor, IN sensor and WR sensor output level check	Check the following signals by using the CU/ PU board HPSNS and RGSNS connector : HPSNS 2pin: Hopping sensor RGSNS 5pin: IN sensor RGSNS 2pin: WR sensor Confirm that the above signal levels change when the sensor lever is operated.	Replace the appropriate sensor(s).

Jam occurs immediately after the paper feed is started.

Check item	Checking method	Action
Check condition of the paper running path
Paper running path of the front unit	Check if paper is jammed or not in the paper running path.	Remove the jammed paper.
Check condition of the mechanical parts
Hopping sensor, IN sensor and WR sensor lever check	Check the sensor lever shapes and operations for any problem	Replace the sensor lever(s) with proper one(s).
Motor operation check
Paper feed motor	Confirm that the paper feed motor works normally by using the Motor & Clutch Test of the self-diagnostic mode.	Replace the CU/ PU board or the feed motor.
Paper feed motor driver	Pull out the CU/PU board HOP connector, and check the following at the side of the connector: Between 1pin – FG: Several MΩ Between 2pin – FG: Several MΩ Between 3pin – FG: Several MΩ Between 4pin – FG: Several MΩ	Replace the CU/PU board.
Clutch operation check
Feed clutch and regist clutch	Confirm that the feed clutch and regist clutch works normally by using the Motor & Clutch Test of the self-diagnostic mode. Pull out the cassette for the rollers to be seen, and check operation.	Replace the CU/ PU board or the feed clutch or regist clutch.
Check the system connection
Paper feed motor drive cable	Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not. Check also that cables are assembled without any abnormality.	Replace the cable with the good cable that normalizes the connection condition.
	Pull out the CU/PU board HOP connector, nd check the following at the side of the connector: Between 1pin – FG: Do not short-circuit Between 2pin – FG: Do not short-circuit Between 3pin – FG: Do not short-circuit Between 4pin – FG: Do not short-circuit	Replace the cable with the good cable that normalizes the connection condition.
Feed clutch cable	Check the connection condition of the cable. Check if the connector is connected in the half-way only or not, and check if the connector is inserted in a slanted angle or not.	Normalizes the connection condition. Replace the clutch.
Feed clutch	Pull out the CU/PU board HOC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240Ω	Replace the clutch and properly assemble appropriate parts.
Regist clutch	Pull out the CU/PU board REC connector, and check the following at the side of the connector. Between 1pin – FG: Do not short-circuit Between 1pin – 2pin: About 240Ω	Replace the clutch and properly assemble appropriate parts.
Paper feed motor	Pull out the CU/PU board HOP connector, and check the following at the side of the connector. Between 1pin – 2pin: 3.4Ω or 5Ω Between 3pin – 4pin: 3.4Ω or 5Ω	Replace the Paper feed motor.