OKI B432dn

Maintenance mode includes the following.

• "Admin Menu" and "Boot Menu" which is shown by an end user.
• "Service Menu" , "System Maintenance Menu" and "Engine Maintenance Mode" for the member of maintenance that is not shown by an end user.
• "Factory Maintenance Menu" to use in production in a factory.

To view each category, push the button of "MENU▲" and "MENU▼". After the screen displays the last category, the display returns to the first category. If want the displayed function to be effective, push the "OK" button. For terminating the mode that is in category displaying, push the key of "ON LINE" and return to operation mode.

Admin Menu

An usual menu is similar, and Admin Menu enters a menu by pushing "Menu▲" or "MENU▼" button from a Ready state and selects "ADMIN MENU".

Enters a password is necessary for "ADMIN MENU".
The default value of password is "aaaaaa".
Except an item about emulation / interface, show a function in the following.

Item		Value	Function / Notes
PANEL SETUP	NEARLIFE STATUS	ENABLE DISABLE	Sets up LED display control for the occurrence of a near life warning of a drum. A near life warning is displayed when Enable is set. A near life warning is not displayed when Disable is set. (It is also not output to any of Attention LED/PJL/ MIB/Web.) A status (life warning) of temporal recovery by opening and closing the cover in a life error state is not included.
	NEARLIFE LED	ENABLE DISABLE	Sets up LED lighting control for the occurrence of a near life warning of a toner or drum Attention LED is lighted when Enable is set.* Attention LED is not lighted when Disable is set. The status (life warning) of temporal recovery by opening and closing the cover in a life error state is not included. * It applies to drums when "PANEL SETUP" - "NEARLIFE STATUS" is set to "ENABLE". It always applies to toner regardless of the setting of "PANEL SETUP" - "NEARLIFE STATUS".
POWER SETUP	AUTO PW OFF	ENABLE AUTO CONFIG DISABLE	Set the behavior of Auto Power Off. ENABLE: The printer goes to Off mode even if LAN cable is connected. AUTO CONFIG: The printer does not go to Off mode when LAN cable is connected, goes to Off mode when USB or Centro cable is connected. DISABLE: Invalidate to go to Off mode by time.
	POWER RETURN	MANUAL STATE CONTINUE	Set the power on method after energize.
TRAY SETUP	UNIT OF MEASURE	INCH MILLIMETER	Specifies the unit of custom paper size.
	DEFAULT PAPERSIZE	A4 LETTER	Set default paper size.
OTHERS SETUP	RAM SETUP	RECEIVE BUF SIZE	Sets the size of receive buffer
		RESOURCE SAVE	Sets the size of resource saving area. This Item does not appear in Non-PS models.
	FLASH INITIALIZE	EXECUTE	Initializes the range of open area of Flash (displayed on File List). When the OK key is pressed, the following confirmation message appears. ARE YOU SURE? YES/NO If NO is selected, the previous menu display resumes. If YES is selected, the following confirmation message appears. EXECUTE NOW? YES/NO If NO is selected, the previous menu display resumes. At this time, the request to execute FLASH initialization is put into the memory and initialization will be executed at power cycle. If YES is selected, reboot takes place, and FLASH is initialized at rebooting cycle.
	FLASH SETUP	FORMATTING	Formats a specified partition. When the OK key is pressed, the following confirmation message appears. ARE YOU SURE? YES/NO If NO is selected, the previous menu display resumes. If YES is selected, the following confirmation message appears. EXECUTE NOW? YES/NO If NO is selected, the previous menu display resumes. At this time, the request to execute partition formatting is put into the memory and formatting will be executed at power cycle. If YES is selected, reboot takes place and the partition is formatted at rebooting cycle.
	STORAGE SETUP	ENABLE INITIAL	Prevents a setting change accompanying initialization of Block Deveice(FLASH).
	JOB LOG SETUP	SAVE JOB LOG
		CLEAR JOB LOG
	SETTINGS	MENU RESET	Resets EEPROM of CU. Resets User menu to the factory default. If Execute is selected, It exits from the menu after the COMPLETE character is displayed. However, when this function is executed with PJL, WINDOW named COMPLETE is not displayed.
		SAVE MENU	Saves menus currently set. With this function, the menus with which operation was last performed are saved, and overwrites with them menus that were previously saved. When the Enter switch is pressed, the following confirmation message appears. ARE YOU SURE? YES/NO When NO is selected, next preceding menus are restored. When YES is selected, the current menu settings are saved and this menu is exited.
		RESTORE MENU	Changes to the menu setting saved. When the Enter switch is pressed, the following confirmation message appears. ARE YOU SURE? YES/NO If NO is selected, the previous menu display resumes. If YES is selected, changes to the menu setting saved and exit from the menu. *It will not be executed when there is the printing data.
	NEW PASSWORD	************	Allows the password to be changed for the menu's lockout function. The underline indicates the entry position. A number from 0 to 9 and character from a to z can be entered for each digit. * It is possible to move between digits after entering a number.
	VERIFY PASSWORD	************	Verifies the above password. The underline indicates the entry position. A number from 0 to 9 and character from a to z can be entered for each digit.