OKI B431
Maintenance Mode. System Maintenance Menu
To open System Maintenance Menu, hold down the "MENU▲" and "MENU▼" button and turn on the power switch. After the Category has been displayed, let go of the "MENU▲" and "MENU▼" button.
| Category | Setting item (Upper case) | Setting item (Lower case) | Function |
|---|---|---|---|
| OKIUSER (*1) | OKIUSER | ODA OEL APS JP1 JPOEM1 OEMA OEML |
Set the destination. JPOEM1: Japan Oriented OEM OEMA: Overseas OEM for A4 default OEML: Overseas OEM for Letter default After passing the MENU, it reboots automatically. If the Japanese font exist, JP1 is default. |
| MAINTENANCE MENU | FLASH FORMAT | EXECUTE | Initialize Flash ROM. After executing it passes the MENU. The format of Flash Device that is implemented on resident (on board) starts. |
| MENU RESET | EXECUTE | Reset the EEPROM content to the (Factory Default) setting value . After the setting alteration, it reboots automatically. * Part of special item is not initialized. |
|
| CONFIG MENU | CODESET | TYPE1 TYPE2 |
This MENU displays as all destination. TYPE1: Non display of Russian / Grace TYPE2: Display Russian / Grace. After passing the MENU, it reboots automatically. For destination of OEL/APS/OEMA, TYPE2 is default value. For other destinations, TYPE1 is default value |
| TEST PRINT MENU | TEST PRINT MENU | ENABLE DISABLE |
Switch between whether to display ENGINE INFORMATION that is on the INFORMATION MENU Category of USER MENU. If this item is Disable, ENGINE INFORMATION is not often displayed. |
| FUSE KEEP MODE | FUSE KEEP MODE | EXECUTE | While press ENTER Key the command is send from CU to PU and then it becomes ONLINE. Replace the consumable by the new one and check the operation as the power ON. (At this moment, the fuser of new consumable is not cut and the operation count is not added to the value of old consumable. While turn the power OFF the check mode is terminated. Till the next time of power ON it is Disable. |
| DOTSHIFT (*1) | TRAY1 | -4.0MILLIMETER ~ -1.5MILLIMETER -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER |
Set landscape dot Shift of Tray 1 while printing. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. |
| TRAY2 | -4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER |
Set landscape dot Shift of Tray 1 while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. | |
| MANUAL | -4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER |
Set landscape DOTSHIFT of Manual Slot while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. Only B411 is used. | |
| MPT | -4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER |
Set landscape DOTSHIFT of MPT while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. Only B431 is used. | |
| ENGINE DIAG MODE | Included in Engine Maintenance Menu. |
(*1) can be set by "Maintenance Utility".