OKI B430

For System Maintenance Menu, hold down the "MENU▲" and "MENU▼" button and turn on the power switch. After the Category has been displayed, let go of the "MENU▲" and "MENU▲" button.

Category	Operation panel display		Default value	Function * Only English is supported for panel display
	Setting item (Upper case)	Setting item (Lower case)
OKIUSER	OKIUSER	ODA OEL APS  JP1 JPOEM1 OEMA OEML	*	Set the destination. JPOEM1: Japan Oriented OEM OEMA: Overseas OEM for A4 default OEML: Overseas OEM for Letter default After passing the MENU, it reboots automatically. If the Japanese font exist, JP1 is default.
MAINTENANCE MENU	FLASH FORMAT	EXECUTE	-	Initialize Flash ROM. After executing it passes the MENU. The format of Flash Device that is implemented on resident (on board) starts.
	MENU RESET	EXECUTE	-	Reset the EEPROM content to the (Factory Default) setting value . After the setting alteration, it reboots automatically. * Part of special item is not initialized.
CONFIG MENU	CODESET	TYPE1 TYPE2	*	This MENU displays as all destination. TYPE1: Non display of Russian / Grace TYPE2: Display Russian / Grace. After passing the MENU, it reboots automatically. For destination of OEL/APS/OEMA, TYPE2 is default value. For other destinations, TYPE1 is default value.
TEST PRINT MENU	TEST PRINT MENU	ENABLE DISABLE	*	Switch between whether to display ENGINE INFORMATION that is on the INFORMATION MENU Category of USER MENU. If this item is DISABLE, ENGINE INFORMATION is not often displayed.
FUSE KEEP MODE	FUSE KEEP MODE	EXECUTE	-	While press ENTER Key the command is send from CU to PU and then it becomes ONLINE. Replace the consumable by the new one and check the operation as the power ON. (At this moment, the fuser of new consumable is not cut and the operation count is not added to the value of old consumable. While turn the power OFF the check mode is terminated. Till the next time of power ON it is DISABLE.
PERSONALITY	PCL	ENABLE DISABLE	*	Change the default of Support PDL Language for each destination. The PDL Language that is DISABLE in this MWNU is not displayed on the OP MENU of EMULATE and Administrator MENU of User Menu. (About "PCL XL", because it does not have specified menu, no appearance change is shown even at DISABLE.) As receiving the printing data of DISABLE PDL Language, it displays INVALID DATA and discards the received data. In the case that set the Japan Oriented "IBM PPR III XL" and "EPSON FX" as ENABLE, the operation is not guaranteed. "PS3 EMU" is only displayed at PSE implementation. It means Read Only While "PCL" can not be set as DISABLE. (Normally, it is used by ENABLE. Even set as DISABLE it still process received data. Default Value: For Japan Oriented equipment sets "IBM PPR" and "EPSON FX" as DISABLE, yet "ESC/P" as ENABLE. For Non Japan Oriented equipment sets "IBM PPR" and "EPSON FX" as ENABLE, yet "ESC/P" as DISABLE.
	IBM PPR III XL	ENABLE DISABLE	*E *J
	EPSON FX	ENABLE DISABLE	*E *J
	ESC/P	ENABLE DISABLE	*J *E
	PS3 EMULATION	ENABLE DISABLE	*
	PCL XL	ENABLE DISABLE	*
ROLLING ASCII	ROLLING ASCII	EXECUTE		Set PRINTING Rolling ASCII as continuously printing. Set Rolling ASCII Paten as continuously printing. Press "ENTEN" switch at this menu displaying. After EXECUTE displayed in the lower case, press "ENTER" switch to settle the execution. Press "ON-LINE" switch to initialize and then continuously printing is available. For the termination of this mode, it is to press "ON-LINE" switch and wait for printing stopped, and then shut down power or press "CANCEL" switch. After this operation it can not return to any other maintenance mode.
DOTSHIFT	TRAY1	-4.0MILLIMETER ~ -1.5MILLIMETER -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER	*	Set landscape dot Shift of Tray 1 while printing. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized.
	TRAY2	-4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER	*	Set landscape dot Shift of Tray 1 while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized.
DOTSHIFT	MANUAL	-4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER	*	Set landscape DOTSHIFT of Manual Slot while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. Only B410/B420 Series is displayed.
	MPT	-4.0MILLIMETER ~ -1.0MILLIMETER -0.5MILLIMETER 0.0MILLIMETER +0.5MILLIMETER ~ +3.5MILLIMETER		Set landscape DOTSHIFT of MPT while printing. Item is displayed even Tray 2 is not implemented. In this area, even EEPROM RESET such as ROM Ver.UP is not initialized. Only B430/B440 Series is displayed.
ENGINE DIAG MODE			-	Included in Engine Maintenance Menu.