Error code |
Description |
Action |
202.33 |
Bin-full sensor is never made or is made late. |
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Pick arm stuck down service check”. |
202.34 |
Bin-full sensor broke early.
Possible causes:
- Incorrect paper settings
- Defective bin-full sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Go to “Pick arm stuck down service check” .
|
202.35,
202.37 |
Bin-full sensor does not break or breaks late.
- Incorrect paper settings
- Incorrect paper loaded
- Incorrect paper guide setting
- Bin-full sensor failure
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Flex the media, and stack it flat in the paper tray.
- Properly set the paper guides in the paper tray.
- Check the pick roll tires, and replace them if they are worn.
- Go to “Pick arm stuck down service check” .
|
202.38 |
Bin-full sensor is never made or is made late. |
See “202.33”. |
202.39 |
Fuser motor stalled.
Possible causes:
- Faulty cable/connector
- Faulty fuser motor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “120.xx—Motor (fuser) error service check”. |
202.51 |
Exit sensor is made when the printer tries to print from an idle state.
(Fuser past life) |
See “202.01”. |
202.52 |
Exit sensor is made early.
(Fuser past life) |
See “202.02”. |
202.53 |
Exit sensor is never made.
(Fuser past life) |
See “202.03”. |
202.54 |
Exit sensor broke early.
(Fuser past life) |
See “202.04”. |
202.55,
202.57 |
Exit sensor never broke.
(Fuser past life) |
See “202.05, 202.07” on page 2-11. |
202.58 |
Exit sensor is never made.
(Fuser past life) |
See “202.03”. |
203.01 |
Redrive bubble sensor is made when the printer powers up or covers are closed. |
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Redrive bubble sensor service check”. |
203.02 |
Paper hit the redrive bubble sensor too soon.
Possible causes:
- Damaged redrive bubble sensor or redrive bubble sensor flag
- Loose redrive bubble sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- The redrive bubble sensor may not be functioning properly. Go to “Redrive bubble sensor service check”.
|
203.03 |
Redrive bubble sensor is never made or is made late.
Possible cause: Faulty redrive bubble sensor |
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Redrive bubble sensor service check”. |
203.04 |
Redrive bubble sensor flag broke early.
Possible causes:
- Incorrect paper settings
- Defective redrive bubble sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media used.
- Go to “Redrive bubble sensor service check”.
|
203.05,
203.07 |
Redrive bubble sensor does not break or breaks late.
Possible causes:
- Incorrect paper settings
- Redrive bubble sensor failure
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media used.
- Go to “Redrive bubble sensor service check”.
|
203.08 |
Redrive bubble sensor is never made or is made late. |
See “202.03” . |
203.21,
203.22 |
Paper path redrive motor stalled or is under speed.
Possible causes:
- Faulty paper path redrive motor
- Faulty cable/connector
- Faulty system board
|
- Check that the waste toner container is latched correctly in the printer.
- Check for anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “149.xx—Paper path redrive motor error service check”. |