Error code |
Description |
Action |
200.01 |
Input sensor is made when printer powers up or covers are closed.
Possible causes:
- Paper jam leaving page over sensor
- Defective input sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Input, S1, narrow media, and near narrow media sensor service check” . |
200.02 |
Paper hit the input sensor too soon.
Possible causes:
- Damaged input sensor flag or input sensor
- Loose input sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- The input sensor may not be functioning properly. Go to “200.02—Paper Jam error service check” .
|
200.03 |
Input sensor is never made or made late.
Possible causes:
- Faulty input sensor
- Faulty staging deflector assembly
- Faulty autocomp assembly
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “200.03, 200.08—Paper Jam error service check” . |
200.04 |
Input sensor flag broke early.
Possible cause:
- Incorrect paper settings
- Faulty input sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Go to “Input, S1, narrow media, and near narrow media sensor service check” .
|
200.05,
200.07 |
Input sensor does not break or breaks late.
Possible causes:
- Incorrect paper settings
- Incorrect paper loading
- Incorrect paper guide setting
- ITU module failure
- Lower guide failure
- Paper pick mechanism failure
- Input sensor failure
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Flex the media, and stack it flat in the paper tray.
- Properly set the paper guides in the paper tray.
- Check the pick roll tires, and replace them if they are worn.
- Go to “200.05, 200.07—Paper Jam error service check” on page 2-104.
|
200.08 |
Input sensor is never made or made late. |
See “200.03” . |
200.21,
200.22 |
Staging motor stalled or is under speed.
Possible causes:
- Faulty staging motor
- Faulty cable/connector
- Faulty system board
|
- Check that the waste toner container is latched correctly in the printer.
- Check for anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “147.xx—Staging motor error service check” . |
200.31 |
Near narrow media sensor is made when the printer tries to print from an idle state.
Possible causes:
- Paper jam leaving paper over the sensor
- Defective near narrow media sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Input, S1, narrow media, and near narrow media sensor service check” . |
200.32 |
Near narrow media sensor is never made or is made late.
- Damaged narrow media flag or narrow media sensor
- Loose input sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “200.32—Paper Jam error service check” . |
200.33 |
Near narrow media sensor is never made or is made late.
- Faulty input sensor
- Faulty staging deflector assembly
- Faulty autocomp assembly
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “200.33, 200.38—Paper Jam error service check” . |
200.34 |
Near narrow media sensor broke early.
Possible causes:
- Incorrect paper settings
- Defective near narrow media sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Go to “Input, S1, narrow media, and near narrow media sensor service check” .
|
200.35,
200.37 |
Near narrow media sensor does not break or breaks late.
- Incorrect paper settings
- Incorrect paper loaded
- Incorrect paper guide setting
- ITU module failure
- Lower guide failure
- Paper pick mechanism failure
- Near narrow media sensor failure
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Flex the media, and stack it flat in the paper tray.
- Properly set the paper guides in the paper tray.
- Check the pick roll tires, and replace them if they are worn.
• Go to “200.35, 200.37—Paper Jam error service check” . |
200.38 |
Near narrow media sensor is never made or is made late. |
See “200.33” . |
200.40 |
S1 sensor is made early.
Possible causes:
- Incorrect paper settings
- Defective S1 sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- If clearing a paper jam does not fix the problem,
go to “241.02—Paper Jam error service check” . |
200.41 |
Narrow media sensor is made when printer tries to print from an idle state.
Possible causes:
- Paper jam leaving page over sensor
- Defective narrow media sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “Input, S1, narrow media, and near narrow media sensor service check” . |
200.42 |
Narrow media sensor is made early. Possible causes:
- Incorrect paper settings
- Defective narrow media sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- If clearing a paper jam does not fix the problem,
go to “200.42—Paper Jam error service check” . |
200.43 |
Narrow media sensor is never made or is made late. |
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem,
go to “200.43, 200.48—Paper Jam error service check” . |
200.44 |
Narrow media sensor broke early. Possible causes:
- Incorrect paper settings
- Defective narrow media sensor
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Go to “Input, S1, narrow media, and near narrow media sensor service check” .
|
200.45 |
Narrow media sensor does not break or breaks late.
- Incorrect paper settings
- Incorrect paper loaded
- Incorrect paper guide setting
- ITU module failure
- Lower guide failure
- Paper pick mechanism failure
- Narrow media sensor failure
|
- Clear away anything in the paper path that might cause the paper to jam.
- Be sure the paper settings match the media.
- Flex the media, and stack it flat in the paper tray.
- Properly set the paper guides in the paper tray.
- Check the pick roll tires, and replace them if they are worn.
- Go to “200.45, 200.47—Paper Jam error service check”.
|
200.47 |
Narrow media sensor does not break or breaks late. |
See “200.45” . |
200.48 |
Narrow media sensor is never made or is made late. |
|
200.49 |
S1 sensor is made when printer tries to print from an idle state.
Possible causes:
- Paper jam leaving paper over the sensor
- Defective near narrow media sensor
- Faulty system board
|
- Clear away anything in the paper path that might cause the paper to jam.
- If clearing a paper jam does not fix the problem, go to “Input, S1, narrow media, and near narrow media sensor service check” .
|