Konica-Minolta bizhub 215

5 ADF FEED TEST

• To check for correct paper passage of the paper take-up and transport system in the ADF alone as a single unit.
• Here are the details of operation involved in the paper passage motion.
  ◦ The Scanner does not make any scan motion.
  ◦ Paper passage operation continues until all pages of the document loaded in the unit have been fed in.
• When a paper misfeed of originals occurs

Procedure

1. Call the SERVICE MODE to the screen.
2. Select [FUNCTION], and press the OK key.
3. Select [ADF FEED TEST], and press the OK key.
4. Load paper in the ADF.
5. Use [▲/▼] key to select a scanning Mode, and press the Start key to start the ADF feed test.
   Press the Stop key to stop the ADF feed test.
   Scanning Mode
   • BW 300dpi, BW 600dpi, COLOR 150dpi, COLOR 300dpi
   • 1-SIDE, 2-SIDE

6 COPY ADF GLASS

• To check for scratches and dirt on the Original Scanning Glass.
• When a dirty image occurs

Procedure

1. Call the SERVICE MODE to the screen.
2. Select [FUNCTION], and press the OK key.
3. Select [COPY ADF GLASS].
4. Press the OK key to start the Copy ADF Glass Area test.
5. The copier produces two copy samples.

NOTE
• If the image on the copy contains stripes, clean or replace the original scanning glass.

7 UPLOAD F/W

It will be displayed only when the optional FAX kit FK-510 is mounted.

• Download firmware from this machine to remote side, after setup of remote side location.
• Machine will dial automatically and copy the firmware to remote side machine.

Procedure

1. Call the SERVICE MODE to the display.
2. Select [FUNCTION], and press the OK key.
3. Select [UPLOAD F/W], and press the OK key.
4. Enter the remote side destination, and press the ▼ key.
5. Enter the password (4-digits), and press the OK key.
6. Press the Start key.

8 FAX RES. COPY TEST

It will be displayed only when the optional FAX kit FK-510 is mounted.

• Print TX page of fax operation, make a copy test of the fax resolution.
• To check whether or not the encoding/decoding process is correct.

Procedure

(a) CIS.FAX

1. Call the SERVICE MODE to the display.
2. Select [FUNCTION], and press the OK key.
3. Select [FAX RES. COPY TEST], and press the OK key.
4. Select [CIS.FAX], and press the OK key.
5. Select [AUTO DETECTION], and press the OK key. Or select [MANUAL: XX], and press the ► key. Then, select the scan size and press the OK key.
6. Press the OK key to scan the next original and the Back key to finish the scanning.
7. Start the scanning.

(b) ADF.FAX

1. Call the SERVICE MODE to the display.
2. Select [FUNCTION], and press the OK key.
3. Select [FAX RES. COPY TEST], and press the OK key.
4. Select [ADF.FAX], and press the ► key.
5. Select [1-SIDE] or [2-SIDE], and press the OK key.
6. Set the original on ADF, and press the OK key.
7. Start the scanning.

9 SCAN TEST

• To check that the exposure lamp turns ON properly and the scanner moves properly.
• Used when the scan motion is faulty.

Procedure

1. Press the OK key to start the scan test.
2. Pressing the Stop key will stop the scan test.

10 TONER SUPPLY

• To adjust the set T/C level by replenishing an auxiliary supply of toner when a low ID occurs due to a lowered T/C after large numbers of prints have been made of originals having a high image density.

Procedure

1. Press the OK key to start the toner supply function.
2. When the toner density returns to normal or a given period of time elapses after the toner supply is started, the machine automatically stops supplying toner.