Canon imageCLASS MF9340C

FRT-TS-C

Transfer bias front side setting value (C) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

FRT-TS-K

Transfer bias front side setting value (Bk) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

BCK-TR-Y

Transfer bias backside setting value (Y) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

BCK-TR-M

Transfer bias backside setting value (M) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

BCK-TR-C

Transfer bias backside setting value (C) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

BCK-TR-K

Transfer bias backside setting value (Bk) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for toner scatter/dotted image)
• Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
• It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]

PGR-YMCK

Setting value of transfer bias between sheets (Y, M, C, Bk) [When used]
The density of the entire area of 70 to 80mm from the leading edge of the sheet is low/high, or there are an infinite number of white or black spots in an image when the entire print is halftone, etc.
[Adjustment method]

• The problem may be eliminated by changing the setting value.
• Increase the setting value. (Effective for thin density in the area 70 to 80mm from the leading edge)
• Decrease the setting value. (Effective for high density in the area 70 to 80mm from the leading edge) Setting range: -20 to 50 (Unit: 50V)

[Factory setting value/Value after RAM clearing: 0]

FRT-ATH

Attraction bias front side setting value [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value. Setting range: -20 to 20 (Unit: 100V)
[Factory setting value/Value after RAM clearing: 0]

• When an image is not firmly fixed to the sheet, the problem may be eliminated by increasing the setting value.
• When a residual image remains in an image, the problem may be eliminated by decreasing the setting value. Setting range: -4 to 4 (Unit: Approx. 5 degree C)

• When an image is not firmly fixed to the sheet, the problem may be eliminated by increasing the setting value.
• When a residual image remains in an image, the problem may be eliminated by decreasing the setting value. Setting range: -4 to 4 (Unit: Approx. 5 degree C)