| Error Code |
Description |
| 009A |
Can't detect any signal after sending CI signal. |
| 009D |
Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx. |
| 009E |
Manual Tx over 15 minutes whin in phase C by non-ECM mode. |
| 00A0 |
User stop or cancel transmission job. |
| 00A1 |
Document JAM within transmission |
| 00AE |
Can't finished V.8 procedure or detect V.21 signal after CM signal |
| 00AF |
Modem can't enter into control channel after TX side sending out RCP signal for V34 |
| 00B1 |
Can't finish V.8 procedure or detect V.21 signal after ANSam signal within 35 sec. |
| 00B2 |
Can't detect phase 2 signal after our side sending CJ signal within 30 sec |
| 00B3 |
Can't detect correct V.21 or JM signal after sending CM or CJ signal. |
| 00B4 |
Can't detect correct phase 2 signal within 25 second after CM/JM signal exchange. |
| 00B5 |
Can't detect phase 3 signal after Phase 2 |
| 00B6 |
Can't detect phase 4 signal within 25 sec after CM/JM exchange. |
| 00B8 |
Remote side disconnect after our side sending DCS signal in V.34. |
| 00BA |
Cannot received correct signal after our side sending DTC signal in V.34. |
| 00BB |
Every time our side received DIS signal after sending DTC in V.34. |
| 00BC |
Modem can't ready within 10 second after entering primary channel in V.34. |
| 00BD |
Can't detect correct V.21 or JM signal after detected FSK frequency. |
| 00BE |
Remote side no document to be polled after V.8 handshaking. |
| 00BF |
Capability no match after V.8 handshaking |
| 00C1 |
At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving unit. |
| 00C2 |
Remote side disconnect after sending out V.8 CM signal. |
| 00C4 |
After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN. |
| 00C5 |
Received DCN signal after sending MPS signal. |
| 00C9 |
At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit. |
| 00CA |
After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP. |
| 00CB |
After sending EOP signal, the received is DCN signal. |
| 00CF |
Received incorrect signal after sending DTC signal for V.34 polling. |
| 00D0 |
Received ERR signal after sending EOR_NULL. |
| 00D1 |
Received incorrect response after sending PPS_EOP signal |
| 00D2 |
Received DCN after sending PPS EOP signal |
| 00D3 |
Received DCN after sending PPS NULL signal |
| 00D8 |
Can't detect correct phase 3 signal for poling. |
| 00D9 |
Can't detect correct phase 3 signal after detect silence after phase 2. |
| 00DA |
Can't detect phase 4 signal within 30 sec. |
| 00DB |
Can't received any T.30 signal within 30 sec within phase 4. |
| 00DC |
Received T.30 signal in phase 4 other than DCS, DIS or DTC |
| 00DE |
Remote side no SUB capability. |
| 00E0 |
At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer. |
| 00E1 |
Received incorrect response after sending PPS_NULL. |
| 00E2 |
Can't receive any response in RR response procedure after sending PPS_NULL. |
| 00E3 |
At phase D, transmitting units out PPS_MPS 3 times consecutivery but receive no answer. |
| 00E4 |
Received incorrect response after sending PPS_MPS signal |
| 00E6 |
Can't receive any response in RR response procedure after sending PPS_MPS. |
| 00E7 |
Reseived DCN after sending PPS MPS. |
| 00E8 |
At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer. |
| 00E9 |
Receive PIN signal after sent last page data. |
| 00EA |
Can't receive any response in RR response procedure after sending PPS_EOP. |
| 00EE |
At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer. |
| 00EF |
Received incorrect response after sending EOR_NULL. |
| 00F0 |
Can't receive any response in RR response procedure after sending EOR_NULL. |
| 00F1 |
At phasa-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer. |
| 00F2 |
Received incorrect response after sending EOR_MPS. |
| 00F3 |
Received ERR signal after sending EOR_MPS. |
| 00F4 |
Can't receive any response in RR response procedure after sending EOR_MPS. |
| 00F5 |
At phasa-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer. |
| 00F6 |
Received incorrect response after sending EOR_EOP |
| 00F7 |
After Received ERR, our side can't received response after sending EOR_EOP command. |
| 00FC |
Can't receive any response after sending CTC. |
| 00FD |
Can't speed down to lower speed. |
| 00FE |
Memory full for transmission |
| 00FF |
REDAIL ALL FAIL |