| Error Code |
Description |
| 0001 |
Nothing G3 signal received within 35 sec. |
| 0003 |
Received DIS after sending DIS signal |
| 0004 |
Received DCN after sending DTC signal |
| 0009 |
Can't receive any signal within 35 sec. in manual polling mode. |
| 0010 |
Received DCN signal after sending DTC signal in Polling Rx. |
| 0011 |
Can't receive any correct response after sending DTC signal. |
| 0012 |
Remote side Password not match in Polling Rx/our side no any file to be polling. |
| 0013 |
Can't receive carrier within 6 sec. after sending CFR in date phase C. |
| 0014 |
Can't receive T.30 signal after sending FTT signal. |
| 0016 |
Receive DCN signal after sending PTT signal. |
| 0017 |
Can't receive any response from remote side after sending DIS |
| 0018 |
Can't detect energy within 6 sec after sending FTT command |
| 0019 |
Received DCN signal sending CFR signal |
| 001A |
No energy on line over 6 sec. within phase C before any corrected ECM frame. |
| 001D |
Can't detect flag after sending CFR signal |
| 001E |
Timeout in V.17 ECM Rx phase C |
| 0020 |
Can't correct frame within 6 sec at phase C. |
| 0021 |
File full. |
| 0022 |
Owing to noise interference on the line, receiving side can't receive correct data within specified time (no ECM) |
| 0023 |
Can't receive correct signal after sending CFR signal |
| 0030 |
Can't receive any signal within 6 sec. At phase D. |
| 0031 |
Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc) |
| 0032 |
Can't receive carrier within 6 sec after sending MCF or RTP, RTN signal |
| 0033 |
Received DCN signal at ohase D within pages (not last page). |
| 0039 |
In non_ECM mode, when machine alredy received the data dosen't receive 13.1 seconds |
| 001F |
Can't detect any G3 signal within 35 sec after sending DTC signal |
| 003F |
Remote side TSI not define in machine one touch or speed dial directory |
| 0040 |
Can't receive carrier within 6 sec. after sending CTR. |
| 41 |
Can't receive carrier within 6 sec. after sending PPR. |
| 42 |
Can't receive correct signal after sending RNR signal |
| 43 |
Receive incorrect signal at phase D in ECM mode. |
| 44 |
Can't receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode. |
| 47 |
Can't receive correct signal or DCN received after sending ERR signal. |
| 48 |
Can't receive correct signal after receive PPS_PRI_Q |
| 004B |
Can't detect correct FSK signal even through detected FSK tone within 6 sec. |
| 004C |
Handshake fail during re-train or between page in V34 Rx. |
| 004E |
Receive DCN signal after sending DIS in V.34. |
| 004F |
Remote side disconnected after sending ANSam in V.8 phase. |
| 50 |
Can't receive any correct signal after detected CJ signal in V.8 phase. |
| 51 |
Can't receive phase 3 signal after phase 2 within 20 seconds in V.34. |
| 53 |
Modem disconnect after phase 4 in V.34. |
| 54 |
Remote side disconnect after phase 4 in V.8 |
| 55 |
Receive incorrect signal after sending DIS signal in V.34 |
| 56 |
Modem disconnect after sending CFR in V.34 |
| 58 |
Can't detect image signal within 6 sec after modem enter to primary phase in V.34 |
| 005A |
Modem cannot detect any correct ECM frame with 3 minutes in phase C. |
| 005B |
Modem can't detect control channel with 12 sec in phase C |
| 005C |
Detect busy tone within control channel after phase C. |
| 005D |
Modem can't detect any correct ECM frame with 12 sec in phase C. |
| 005E |
Can't detect control channel signal after received RCP frame within 6 sec |
| 005F |
Can't detect silence after sending JM signal for polling TX function. |
| 60 |
There are no any bullietin files to be polled in V.34. |
| 61 |
Machine cannot detect V.21 or V.8 signal with 35 sec. |
| 62 |
Modem disconnect in phase D after our side sending out flags sequence in control channel. |
| 63 |
Can't receive any flag sequence in control channel within 25 sec in phase D. |
| 64 |
Can't detect any control channel signal in phase D within 60 sec even through energy still on the line. |
| 65 |
Can't detect any control channel signal within 60 sec after detect sillence in phase D. |
| 66 |
Can't receive T.30 signal or carrier after sending CFR in V.34. |
| 69 |
Capability no match paper size after received is DCS signal. |
| 70 |
User press stop key within receiving. |
| 71 |
Memory full within receiving. |
| 80 |
Can't detect any G3 signal within 35 sec. specified by ITU-T in phase B. |
| 81 |
Received DTC signal in transmission phase. |
| 82 |
Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B. |
| 83 |
Detected FSK signal, but Can't receive any signal within 35 sec. |
| 84 |
Detect DCN signal in phase B. |
| 85 |
Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC |
| 86 |
Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS. |
| 87 |
Training attempt has failed because speed unit can't adjust to low lower speed. |
| 88 |
Received DCN signal after sending out DCS signal |
| 008B |
Receivers protcol of DIS is received, but it is not compatible with our machine. |
| 008C |
Remote side or our side not support capability. |
| 008D |
Receivers protocol of DIS is received, but remote side can't receive document temporary, may because by run out of paper or other reason. |
| 008F |
Modem not ready to received V.34 data within 6 sec after received CFR signal. |
| 90 |
Called side document not ready for our polling. |
| 91 |
Can't receive any commabd after send DCN signal 3 times consecutively |
| 93 |
Received DCN signal after sending out DCN signal |
| 94 |
Time out during transmit ECM frame or RCP command. |
| 95 |
Wrong ID number |
| 96 |
SUBADDRESS/PASSWORD capability not match in polling Rx mode. |