Canon i-SENSYS MF264dw

ADJ-XY

COPIER (Service mode for printer) > ADJUST (Adjustment mode) > ADJ-XY

ADJ-X: Adjust the reading start position

Detail: Decrease the setting value when non-image width is larger than the standard value. Increase the setting value when area outside the original is copied. As the setting value is incremented by 1, the image reading start position moves toward the trailing edge by 0.1 mm.
Use Case: When the reading position of vertical scanning direction at copyboard reading is incorrect
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: -30 to 30
Unit: 0.1 mm
Default Value: 0

STRD-POS: Adjust the reading position: ADF

Detail: As the setting value is incremented by 1, the image reading start position moves toward the leading edge by 0.1mm.
Use Case: When the reading position of vertical scanning direction at ADF stream reading is incorrect
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: -30 to 30
Unit: 0.1 mm
Default Value: 0

ADJ-X-MG: Fine adjust magnification: vertical scan

Detail: To adjust the magnification ratio by comparing the original and the copy output sheet.
- Increase the value when the output sheet is small.
- Decrease the value when the output sheet is large.
Use Case: When the image on copy output sheet is larger or smaller than it is on the original
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Caution: This adjustment is targeted to adjust the image position on copy output. This may affect the SCAN image.
Display/Adj/Set Range: -30 to 30
Unit: 0.1 %
Default Value: 0

CCD

COPIER (Service mode for printer) > ADJUST (Adjustment mode) > CCD

W-PLT-X: Stdrd White Plt white lvl data (X) entry

Detail: To enter the Standard White Plate white level data (X)
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 7000 to 9999
Default Value: 8493

W-PLT-Y: Stdrd White Plt white lvl data (Y) entry

Detail: To Enter the Standard White Plate white level data (Y)
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 7000 to 9999
Default Value: 8988

W-PLT-Z: Stdrd White Plt white lvl data (Z) entry

Detail: To enter the Standard White Plate white level data (Z)
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 7000 to 9999
Default Value: 9176

FBTAR-R Shading target value (R) entry

Detail: To enter the shading target value of RED at copyboard reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 297
Related Service Mode: COPIER > DISPLAY > CCD > FB-TARGET-R

FBTAR-G: Shading target value (G) entry

Detail: To enter the shading target value of GREEN at copyboard reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 294
Related Service Mode: COPIER > DISPLAY > CCD > FB-TARGET-G

FBTAR-B: Shading target value (B) entry

Detail: To enter the shading target value of BLUE at copyboard reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 282
Related Service Mode: COPIER > DISPLAY > CCD > FB-TARGET-B

FBTAR-BW: Shading target value (B&W) entry

Detail: To enter the shading target value of B&W at copyboard reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 296
Related Service Mode: COPIER > DISPLAY > CCD > FB-TARGET-BW

DFTAR-R Shading target value (R) entry: ADF

Detail: To enter the shading target value of RED at ADF stream reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 354
Related Service Mode: COPIER > DISPLAY > CCD > DF-TARGET-R
Supplement/Memo: ADF model only

DFTAR-G: Shading target value (G) entry: ADF

Detail: To enter the shading target value of GREEN at ADF stream reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 349
Related Service Mode: COPIER > DISPLAY > CCD > DF-TARGET-G
Supplement/Memo: ADF model only

DFTAR-B: Shading target value (B) entry: ADF

Detail: To enter the shading target value of BLUE at ADF stream reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 334
Related Service Mode: COPIER > DISPLAY > CCD > DF-TARGET-B
Supplement/Memo: ADF model only

DFTAR-BW Shading target value (B&W) entry: ADF

Detail: To enter the shading target value of B&W at ADF stream reading.
Adj/Set/Operate Method: Enter the setting value, and then press OK or Apply key.
Display/Adj/Set Range: 128 to 384
Default Value: 355
Related Service Mode: COPIER > DISPLAY > CCD > DF-TARGET-BW
Supplement/Memo: ADF model only

PANEL

COPIER (Service mode for printer) > ADJUST (Adjustment mode) > PANEL

TOUCHCHK: Adjust coordinate position: Touch Panel

Detail: To adjust the coordinate position on the Touch Panel of the Control Panel.
Use Case: When replacing the liquid crystal panel.
Adj/Set/Operate Method: Select an item, and press 5 rectangles on the display in order.
Supplement/Memo: Only for Touch Panel model.