Canon i-SENSYS MF249dw

Service Mode. COPIER. OPTION

COPIER > OPTION > BODY
Sub item	Description	ADF model	Other
DFDST-L2	DF dust detection level threshold value (detection after completion of job) Setting range: 0 to 255 (Default value: 100)	Yes	-
LOCALE	To set country group. 1 : Japan 2 : North America 3 : Korea : China : Taiwan : Europe : Asia Setting range: 1 - 7 (Default value: Factory default) Execute the following service mode to enable this setting. COPIER > FUNCTION > CLEAR > ALL	Yes	Yes
ASLPMAX	To change the maximum value of the auto sleep time. 0 : 30 minutes (Default value) 1 : 240 minutes	Yes	Yes
NS-CMD5	Restriction of the use of CRAM-MD5 authentication method at SMTP authentica- tion 0: Dependent on the SMTP server (Default) 1: Not used	Yes	Yes
NS-PLN	Restriction of the use of PLAIN/LOGIN authentication, which is plaintext authen- tication, at SMTP authentication 0: Dependent on the SMTP server (Default) 1: Not used	Yes	Yes
NS-LGN	Restriction of the use of LOGIN authentication at SMTP authentication 0: Dependent on the SMTP server (Default) 1: Not used	Yes	Yes
SDTM-DSP	Setting of automatic shutdown menu display 0: Hide the menu 1: Display the menu	Yes	Yes
WLANPORT	Setting of whether to block transmission to/reception from an unnecessary port with port filter while Wi-Fi Direct is connected 0: Allow transmission to/reception from only the port used by Direct 1: Make the port status same as that of the port at wired side (not blocked)	Yes	Yes
SSLSTRNG	RC4 encryption 0: Normal mode (supported) 1: Secured mode (not supported) (Default)	Yes	Yes

COPIER > OPTION > ACC
Sub item	Description	Common to all models
WLAN	Shows whether the Wireless LAN function is ON/OFF. 0: Forcibly turned OFF (The function is disabled even if the wireless LAN is installed.) 1: ON (Default value)	Yes
WLANMODE	Shows whether the Wireless LAN IEEE 802.11n standard is enabled/disabled. 0: Disabled 1: Enabled (Default value)	Yes
WLANSERIAL	Not in use	-

COPIER > OPTION > SERIAL

Sub item

Description

Common to all models

SN-MAIN

Enter the device serial number written on the rating name plate of the host machine.
<Input procedure>

Write down the value in the "Location" field (blank by default) of System Management Settings from remote UI or local UI. -> In the field, the Controller PCB is replaced with a service part.
Enter the serial number in "Location" of the system management settings, and confirm the serial number. [Menu] > [System Management Settings] > [Device Information Settings] > [Location]
Temporarily enter the serial number in "Location" (8 alphanumeric characters).
Execute this service mode. Check that OK is displayed in COPIER > OPTION > SERIAL > SN-MAIN.
After execution, turn OFF and then ON the power. Perform output only when the entered serial number is 8 alphanumeric characters. After output, the serial number entered in "Location" will be deleted.
After turning ON the power, check the serial number on the system management data list.
Change the setting of "Location" back to the original value. (Enter the value you wrote down in step 1.)

Yes

COPIER > OPTION > FNC-SW
Sub item	Description	Common to all models
CRG-PROC	To set the operation performed when a cartridge reaches the end of life. 0: Not stopped (Default) 1: Stopped once 2: Completely stopped	Yes
CRGLF-K	Reference value for judging "Out" of the component other than toner (Drum/Developing Assembly/waste toner) included in the cartridge life (for Bk) Setting range: 0 to 200 (Default value: 100)	Yes

	Error Code
	Service Mode, Troubleshooting
	Parts Catalog
	Compatibility
	Downloads Files
	Home