Canon Satera MF8350Cdn
Service Mode. COPIER. FUNCTION. 5 SPLMAN 3, INSTALL
SPLMAN
| COPIER > FUNCTION > SPLMAN | ||
|---|---|---|
| SPL68676 | Decrease of paper leading edge margin | |
| Details | To decrease the margin on the leading edge of paper. As the value is incremented by 1, the margin is decreased by 0.1 mm. If the setting is incompatible with SPL65677(increase of margin), the setting is disabled (the margin will be standard). |
|
| Adj/set/operate method |
|
|
| Display/adj/set range | 0 to 20 | |
| Unit | 0.1 mm | |
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL65677 | |
| SPL68677 | Increase of paper right and left margins | |
| Details | To increase the margins on the right and left edges of paper. As the value is incremented by 1, the margin is increased by 0.1 mm. If the setting is incompatible with SPL25607 (decrease of margins), the setting is disabled (the margins will be standard). |
|
| Adj/set/operate method |
|
|
| Display/adj/set range | 0 to 20 | |
| Unit | 0.1 mm | |
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL25607 | |
| SPL25607 | Decrease of paper right and left margins | |
| Details | To decrease the margins on the right and left edges of paper. As the value is incremented by 1, the margin is decreased by 0.1 mm. If the setting is incompatible with SPL68677 (increase of margins), the setting is disabled (the margins will be standard). |
|
| Adj/set/operate method |
|
|
| Display/adj/set range | 0 to 20 | |
| Unit | 0.1 mm | |
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL68677 | |
| SPL93822 | Setting of department ID count all clear | |
| Details | To set whether to disable clearing of all department ID counts. | |
| Adj/set/operate method | Enter the setting value, and then press OK key. | |
| Caution | Be sure to perform this mode after consulting with the system administrator at user's site. | |
| Display/adj/set range | 0 to 1 0: Enabled, 1: Disabled |
|
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL78788 | |
| COPIER > FUNCTION > SPLMAN | ||
| SPL78788 | Setting of department ID count clear | |
| Details | To set whether to disable clearing of department ID count. | |
| Adj/set/operate method | Enter the setting value, and then press OK key. | |
| Caution | Be sure to perform this mode after consulting with the system administrator at user's site. | |
| Display/adj/set range | 0 to 1 0: Enabled, 1: Disabled |
|
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL93822 | |
| SPL41250 | Reset of calibration | |
| Details | When the user allows printing at absence of toner, calibration using toner is disabled. As a remedy, calibration reset is executed by this switch. |
|
| Use case | When the user allows printing after absence of toner is displayed. | |
| Adj/set/operate method | Select the item, and then press OK key. | |
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
| SPL15176 | Extension of detection on absence of toner | |
| Details | Error occurs when the drum running distance reaches a certain point in the case of toner absence. Turning this switch ON delays the occurrence of error (threshold value is changed). |
|
| Use case | When delaying the display of "absence of toner" message | |
| Adj/set/operate method |
|
|
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
INSTALL
| COPIER > FUNCTION > INSTALL | ||
|---|---|---|
| STRD-POS | Scan position auto adj in ADF mode | |
| Details | To adjust the ADF scanning position automatically. | |
| Use case | At ADF installation/uninstallation | |
| Adj/set/operate method |
|
|
| Caution | Write the adjusted value in the service label. | |
| Related service mode | COPIER> ADJUST> ADJ-XY> STRD-POS | |