PrintCopy.info service

Xerox WorkCentre 3215

Error Codes List page 1

  • Code: 01-100
  • Description: Front Cover Open Fault The front cover is open or the cover open switch is defective.
  • Remedy: Check the Actuator on the Front Cover Open Switch. The Actuator moves freely. Y↓N→Replace the Front Cover Open Switch Actuator. (PL-XX) Check the Front Cover Open Switch. The switch is OK. Y↓N→Replace the Front Cover Open Switch. (PL-XX) Check the connection between the Main PWB and the HVPS (BSD 3.1A). The connection is secure. Y↓N→Secure the connection between the Main PWB and HVPS. Replace the HVPS PWB (PL-XX).
  • Code: 03-410
  • Description: Paper Mismatch at Tray 1 The size setting for the Paper Tray does not match the paper size loaded in the tray.
  • Remedy: • Check the media size settings for the tray from the Control Panel. • Adjust the Paper Tray Guides to match the size of the paper that is loaded into the tray. • Place the correct size paper into the tray for the tray size setting.
    Remove the tray and inspect the Paper Size Switch for wear or contamination. The switch is operational. Y↓N→Replace the Paper Size Switch (PL-XX). • Replace the Paper Tray (PL-XX) • Replace the Main PWB, (PL-XX)
  • Code: 03-450
  • Description: Paper Mismatch at Manual Feed Slot The size setting for the Manual Feed Slot does not match the paper size loaded
  • Remedy: • Check the media size settings for the tray from the Control Panel. • Adjust the Paper Tray Guides to match the size of the paper that is loaded into the tray. • Place the correct size paper into the tray for the tray size setting.
    Inspect the Paper Size Switch for wear or contamination. The switch is operational. Y↓N→Replace the Paper Size Switch (PL-XX). • Replace the Paper Tray (PL-XX). • Replace the Main PWB, (PL-XX).
  • Code: 03-900
  • Description: Main PWB Motor Control Chip Fault The Motor Control Chip on the Main PWB is not functioning normally.
  • Remedy: 1. Switch Off the power then switch On the power. 2. If problem continues, replace the Main PWB, (PL-XX).
  • Code: 04-500
  • Description: Main Drive (BLDC) Motor Start Fault The Main Drive (BLDC) Motor did not start within the specified time after the ready signal was sent.
  • Remedy: Enter Diagnostic Mode. Press the <Menu> button, the <#> button, then using the keypad select: [1934, Diagnostics, Machine Test, EDC Mode, DC330 Component Control, 100 Motor] to start the motor. The motor rotates. Y↓N→Remove the Right Cover and check the motor connector on the Main PWB. The connector on the Main PWB is connected correctly. Y↓N→Reconnect the motor connector. Remove the Duplex paper Guide. Check the motor connector. The connector is OK. Y↓N→Reconnect the connector The Imaging Unit Drive coupler may have overloaded. Remove the Print Cartridge and rotate the Imaging Unit coupler. The Imaging Unit coupler rotates freely. Y↓N→Replace the Imaging Unit. The Main Drive Motor or the Main PWB is defective. Perform the following: • Replace the Main Drive Motor PL 4.1. If problem persists, replace the Main PWB, PL 1.1.
  • Code: 05-100, 05-900
  • Description: Paper Jam in Document Feeder Fault The machine has detected a paper jam in the Document Feeder.
  • Remedy: Inspect the Paper Path Sensor for damage or contamination. Remove any debris from the sensor. Enter Diagnostic Mode. Select: [Machine Test, EDC Mode, DC330 Component Control, 102 Sensor, Temp A] to test the Registration Sensor. The sensor is OK. Y↓N→Replace the Paper Path Sensor PL 7.1. Check that the Feed Motor is operating correctly. Select: [Machine Test, EDC Mode, DC330 Component Control, 100 Motor, Feed Motor Slow] The Feed Motor is OK. Y↓N→Check the connection from the Feed Motor to the Main PWB is securely seated. The motor is OK. Y↓N→• Replace the Feed Motor. [PL-XX] • Replace the Document Feed Assembly [PL-XX] Go to SCP 04 Final Actions. Check the paper path drives and clear any jammed sheets from the paper path. If problem persists, replace the Main PWB PL 1.1.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us