Xerox Phaser 8550

• Code: T2A ... T2Z
• Description: T2A T2B T2C T2D T2E T2F T2G T2H T2J T2K T2L T2M T2N T2P T2Q T2R T2S T2T T2X T2Z Exit Door Interlock tripped following an abnormal shutdown. Exit Door Interlock tripped following a normal shutdown. Exit Door Interlock tripped during mechanical recovery Exit Door Interlock tripped during warm-up. Exit Door Interlock tripped during ready state. Exit Door Interlock tripped during a fault state. Exit Door Interlock tripped during an auto drum maintenance cycle. Exit Door Interlock tripped during Printhead maintenance. Exit Door Interlock tripped during Printhead purge. Exit Door Interlock tripped during an oil Transfix Roller cycle. Exit Door Interlock tripped during standby mode. Exit Door Interlock tripped during pick from Tray 2. Exit Door Interlock tripped during pick from Tray 3. Exit Door Interlock tripped during pick from Tray 4. Exit Door Interlock tripped during pick from Tray 1. Exit Door Interlock tripped during duplexing. Exit Door Interlock tripped during transfix staging. Exit Door Interlock tripped during transfixing. Exit Door Interlock tripped during paper exit. Exit Door Interlock tripped during shutdown.
• Causes:
• Remedy: 1. Check for supported media. 2. Check system grounds. 3. Run the Monitor Sensors test using Service Diagnostics. 4. Check the Exit Door Interlock Switch. Replace if necessary. 5. Check the Drum Maintenance Kit is functioning properly and the blade is not covered with ink debris. Replace if necessary 6. Replace the Transfix Roller.

• Code: V2D ... V2X
• Description: V2D V2E V2F V2K V2L V2M V2N V2P V2Q V2R V2S V2T V2X Tray 2 Paper Size Switch activated during warm-up. Tray 2 Paper Size Switch activated during ready state. Tray 2 Paper Size Switch activated during a fault state. Tray 2 Paper Size Switch activated during an oil Transfix Roller cycle. Tray 2 Paper Size Switch activated during standby mode. Tray 2 Paper Size Switch activated during pick from Tray 2. Tray 2 Paper Size Switch activated during pick from Tray 3. Tray 2 Paper Size Switch activated during pick from Tray 4. Tray 2 Paper Size Switch activated during pick from Tray 1. Tray 2 Paper Size Switch activated during duplexing. Tray 2 Paper Size Switch activated during transfix staging. Tray 2 Paper Size Switch activated during transfixing. Tray 2 Paper Size Switch activated during paper exit.
• Causes:
• Remedy: 1. Check system grounds. 2. Check that the Tray 2 media guides are set correctly. 3. Run the Monitor Sensors test using Service Diagnostics. 4. Check the Paper Size Switch. Replace if necessary. 5. Replace the Pivot Arm.

• Code: W2D ... W2X
• Description: W2D W2E W2F W2L W2M W2N W2P W2Q W2R W2V W2S W2T W2X Tray 3 Paper Size Switch activated during warm-up. Tray 3 Paper Size Switch activated during ready state. Tray 3 Paper Size Switch activated during a fault state. Tray 3 Paper Size Switch activated during standby mode. Tray 3 Paper Size Switch activated during pick from Tray 2. Tray 3 Paper Size Switch activated during pick from Tray 3. Tray 3 Paper Size Switch activated during pick from Tray 4. Tray 3 Paper Size Switch activated during pick from Tray 1. Tray 3 Paper Size Switch activated during duplexing. Tray 3 Paper Size Switch activated during an auto drum maintenance cycle. Tray 3 Paper Size Switch activated during transfix staging. Tray 3 Paper Size Switch activated during transfixing. Tray 3 Paper Size Switch activated during paper exit.
• Causes:
• Remedy: 1. Check system grounds. 2. Check that the Tray 3 media guides are set correctly. 3. Run the Monitor Sensors test using Service Diagnostics. 4. Replace the 525-Sheet Feeder.

• Code: W4N, W4P, W2S
• Description: Tray 3 Paper Size Switch activated during pick from Tray 3. Tray 3 Paper Size Switch activated during pick from Tray 4. Tray 3 Paper Size Switch activated during pick from Tray 1.
• Causes:
• Remedy: 1. Check system grounds. 2. Check that the Tray 3 media guides are set correctly. 3. Run the Monitor Sensors test using Service Diagnostics. 4. Replace the 525-Sheet Feeder.

• Code: X2A ... X2X
• Description: X2A X2B X2C X2D X2E X2F X2L X2M X2N X2P X2Q X2R X2S X2V X2W X2X Tray 3 pick flag actuated during an abnormal shutdown. Tray 3 pick flag actuated during a normal shutdown. Tray 3 pick flag actuated during mechanical recovery Tray 3 pick flag actuated during warm-up. Tray 3 pick flag actuated during ready state. Tray 3 pick flag actuated during a fault state. Tray 3 pick flag actuated during standby mode. Tray 3 pick flag actuated during pick from Tray 2. Tray 3 pick flag actuated during pick from Tray 3. Tray 3 pick flag actuated during pick from Tray 4. Tray 3 pick flag actuated during pick from Tray 1. Tray 3 pick flag actuated during duplexing. Tray 3 pick flag actuated during transfix staging. Tray 3 pick flag actuated during an auto drum maintenance cycle. Tray 3 pick flag actuated during drum imaging. Tray 3 pick flag actuated during paper exit.
• Causes:
• Remedy: 1. Check system grounds. 2. Check that the Tray 2 media guides are set correctly 3. Run the Monitor Sensors test using Service Diagnostics. 4. Replace the 525-Sheet Feeder. 5. Replace the Pivot Arm.

• Code: X3D ... X3X
• Description: X3D X3E X3F X3K X3L X3M X3N X3P X3Q X3R X3S X3T X3V X3W X3X Tray 3 pick flag timed-out during warm-up. Tray 3 pick flag timed-out during ready state. Tray 3 pick flag timed-out during a fault state. Tray 3 pick flag timed-out during an oil Transfix Roller cycle. Tray 3 pick flag timed-out during standby mode. Tray 3 pick flag timed-out during pick from Tray 2. Tray 3 pick flag timed-out during pick from Tray 3. Tray 3 pick flag timed-out during pick from Tray 4. Tray 3 pick flag timed-out during pick from Tray 1. Tray 3 pick flag timed-out during duplexing. Tray 3 pick flag timed-out during transfix staging. Tray 3 pick flag timed-out during transfixing. Tray 3 pick flag timed-out during a drum maintenance cycle. Tray 3 pick flag timed-out during drum imaging. Tray 3 pick flag timed-out during paper exit.
• Causes:
• Remedy: 1. Check for supported media. 2. Reduce the amount of media loaded in the tray and reposition the guides to fit snugly against the media. 3. Check the rollers for damage, debris or excessive wear. Clean or replace as necessary. 4. Run the Tray 3 Pick Shaft test using Service Diagnostics. 5. Check system grounds. 6. Push up on the Nudger Roller until it is captured by the Actuator Arm. 7. Run the Pick Clutch test using Service Diagnostics. Replace if necessary. 8. Run the Media Path Drive test using Service Diagnostics. 9. Replace the Pick Roller Assembly. 10. Replace the 525-Sheet Feeder.