Description: Paper Tray 1 Empty Fault The Tray Empty Sensor failed to detect paper in the tray.
Remedy: Check the Tray Empty Sensor actuator. The actuator moves freely is undamaged. Replace the Empty Sensor actuator. Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102 Sensor, Tray 1 Empty] to actuate and de actuate the Tray 1 Empty Sensor. The sensor signal changes. Replace the Tray Empty Sensor. If the problem is intermittent, check the circuit of the Tray Empty Sensor .
Code: 07-130
Description: Paper Jam in Tray 1 Fault A paper jam has occurred in Tray 1.
Remedy: Remove Tray 1 and ensure that guides are set correctly. The paper is loaded correctly in the tray. Align the paper in Tray 1 then reinsert the tray. Check the position of the jammed sheet. The lead edge reached the Retard Roll. (Figure 1.) Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Feed Sens] to block and clear the Feed Sensor. The sensor is OK. Replace the Feed Sensor. In Diagnostics, go to [101-Clutch, Tray 1 Pick up] to energize the clutch. The clutch engages. Replace the Tray 1 Pick up (Feed) Clutch. Perform SCP Final Actions. Remove any jammed paper. Check the following for wear or damage and replace as required: • Retard Roller • Pick up (Feed) and Forward Roll Assembly • Elevator Plate • Elevator Plate Springs
Code: 07-500
Description: Manual Feed Slot Paper Empty Fault The Manual Feed Slot Empty Sensor failed to detect paper in the Manual Feed Slot.
Remedy: Check the Manual Feed Slot Empty Sensor actuator. The actuator moves freely and is undamaged. Replace the Empty Sensor Actuator. Block and clear the Manual Feed Slot Empty Sensor. The sensor signal changes. Replace the Tray Empty Sensor. Check the circuit of the Tray Empty Sensor.
Code: 07-530
Description: Paper Feed Fault - Manual Feed Slot The lead edge was not detected by the Paper Feed Sensor.
Remedy: Check the position of the jammed sheet. The lead edge reached the Retard Roll. Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Feed Sens] to block and clear the Feed Sensor. The sensor is OK. Replace the Feed Sensor . From the EDC menu, select: [101-Clutch, Registration] to engage the drive to pick up paper from tray 1. The clutch engages. Replace the Tray 1 Pick up (Feed) Clutch . Perform SCP Final Actions. Check the Paper Feed actuator. The actuator moves freely is undamaged. Replace the Paper Feed actuator . Inspect the Paper Feed Sensor for damage. The sensor is OK. Replace the Paper Feed Sensor . Check the circuit of the Paper Feed Sensor. .
Code: 08-100
Description: Paper Feed Fault - Tray 1 The lead edge was not detected by the Paper Feed Sensor.
Remedy: Check the Tray 1 Pick up Sensor Actuator. The Actuator moves freely. Replace the Tray 1 Pick up Sensor Actuator. Check the position of the jammed sheet. The lead edge reached the Retard Roll. (Figure 1.) Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 101-Clutch, Tray 1 Pick up] to engage the drive to pick up paper from tray 1 The clutch engages. Replace the Tray 1 Pick up (Feed) Clutch . Check the Paper Feed Actuator. The actuator moves freely. Replace the Paper Feed Actuator. In Diagnostics Mode. Select: [102-Sensor, Feed Sens] to block and clear the Paper Feed Sensor. The signal changes. Replace the Paper Feed Sensor . Perform SCP Final Actions. Check the circuit of the Paper Feed Sensor.
Code: 08-500
Description: Paper Jam in Exit Area Fault The machine has detected a paper jam in the Exit Area.
Remedy: Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Feed Sens] to test the Exit Sensor. The Exit Sensor is OK. Replace the Exit Sensor. In Diagnostics, go to [102-Sensor, Registration] to activate and deactivate the Registration Sensor. The signal changes. Replace the Registration sensor. Inspect the Exit Roller and Drives for wear or damage. Replace if needed.