PrintCopy.info service

Toshiba DP8110

Error Codes List page 1

  • Code: C04
  • Description: Abnormal feed motor
  • Remedy: Is the PFP motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board.
  • Code: C13
  • Description: Abnormal 1st cassette tray (Paper can be fed from cassettes other than the 1st cassette.)
  • Remedy: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C14
  • Description: Abnormal 2nd cassette tray (Paper can be fed from cassettes other than the 2nd cassette.)
  • Remedy: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C15
  • Description: Abnormal 3rd cassette tray (Paper can be fed from cassettes other than the 3rd cassette.)
  • Remedy: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C16
  • Description: Abnormal 4th cassette tray (Paper can be fed from cassettes other than the 4th cassette.)
  • Remedy: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C18
  • Description: Abnormal tandem LCF tray-up motor (Paper can be fed from cassettes other than the tandem LCF cassette.)
  • Remedy: Does the tray move? (Perform the output check in the test mode: 03-270) NO 1. Check if the connector of the tandem LCF tray-up motor is disconnected. 2 Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the LCF tray bottom sensor and LCF tray-up sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[C], /[8]/[A] NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J312 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us