Causes: 0229 1 The CIS is reading the BP belt density to be over 30%. Check the BP belt for ink stains. 0229 2 The paper width or center of the paper detected by CIS is off position over the allowed distance. Check the BP belt for ink stains
Remedy: Do one of the following. • Press the Close button. Note: To solve the problem, the BP belt should be cleaned of the ink or replaced with a new BP belt..
Code: I09
Description: The machine information and control card information do not match.
Causes: 1936 Wrong Control card maybe inserted. Insert correct Control card. This error message displays during the tentative registration between the Engine control PCB and Control card during the machine installation.
Remedy: Check the Control card.
Code: S01
Description: Belt platen transfer error
Causes: 1038 Transfer belt motor locked error 11 30 After the transfer belt motor starts up and the speed stabilizes, the belt HP sensor is not activated in time. 11 31 The belt HP sensor remains activated.
Remedy: Turn OFF the printer. (Turn OFF the printer through sub power key.)
Code: S02
Description: Elevator motor locked
Causes: 1030 Elevator motor locked error
Remedy: Press the Reset key, or turn OFF the printer. (Turn OFF the printer through sub power key.)
Code: S03
Description: Belt platen raising/lowering error
Causes: 2000 The BP elevation motor was driven, but there were not enough motor encoder pulses. 2001 The BP elevation motor was driven, but the printer detected that it did not move. 2002 The belt platen was raised to the upper limit position, but the upper limit sensor was not activated. 2003 The belt platen was raised to the upper limit position, but the lower limit sensor was not deactivated. 2004 The belt platen was raised to the cleaning position, but the upper limit sensor was activated. 2005 The belt platen was raised to the cleaning position, but the lower limit sensor was not deactivated. 2006 The belt platen was lowered to the lower limit position, but the upper limit sensor was not deactivated. 2007 The belt platen was lowered to the lower limit position, but the lower limit sensor was activated. 2008 The belt platen was lowered to the gap adjustment position, but the upper limit sensor was not deactivated. 2009 The belt platen was lowered to the gap adjustment position, but the lower limit sensor did not go OFF. 2010 The BP upper and lower limit sensors for BP elevation were activated at the same time. 2011 BP elevation wires are loose (the BP wire loose detection switch is activated). 2012 1 When the BP unit is elevated to the upper limit position (for regular paper), the rear-left of the BP unit is not detected by the Contact detection mechanism. 2012 2 When the BP unit is elevated to the upper limit position (for regular paper), the rear-right of the BP unit is not detected by the Contact detection mechanism. 2012 3 When the BP unit is elevated to the upper limit position (for regular paper), the front-left of the BP unit is not detected by the Contact detection mechanism. 2012 4 When the BP unit is elevated to the upper limit position (for regular paper), the front-right of the BP unit is not detected by the Contact detection mechanism. 2012 5 When the BP unit is elevated to the upper limit position (for card paper), the rear-left of the BP unit is not detected by the Contact detection mechanism. 2012 6 When the BP unit is elevated to the upper limit position (for card paper), the rear-right of the BP unit is not detected by the Contact detection mechanism. 2012 7 When the BP unit is elevated to the upper limit position (for card paper), the front-left of the BP unit is not detected by the Contact detection mechanism. 2012 8 When the BP unit is elevated to the upper limit position (for card paper), the front-right of the BP unit is not detected by the Contact detection mechanism. 2013 The BP elevation motor was driven, but it did not stop in time. 2014 1 The ink pan and belt platen are stopped in positions not possible during normal operation, and the maintenance unit cannot be initialized. 2014 2 The wiper is not at the origin, and the ink pan cannot function. 2014 3 Ink pan, PB unit, or Wiper did not stop in the same position as in previous position. 2015 1 When the BP unit is elevated to the upper limit position (for envelope), the rear-left of the BP unit is detected by the Contact detection mechanism. 2015 2 When the BP unit is elevated to the upper limit position (for envelope), the rear-right of the BP unit is detected by the Contact detection mechanism. 2015 3 When the BP unit is elevated to the upper limit position (for envelope), the front-left of the BP unit is detected by the Contact detection mechanism. 2015 4 When the BP unit is elevated to the upper limit position (for envelope), the front-right of the BP unit is detected by the Contact detection mechanism.
Remedy: Turn OFF the printer. (Turn OFF the printer through sub power key.)
Code: S04
Description: Ink temperature adjustment error
Causes: 2130 Black ink temperature does not increase. 2131 Cyan ink temperature does not increase. 2132 Magenta ink temperature does not increase. 2133 Yellow ink temperature does not increase. 2134 Black ink temperature does not decrease. 2135 Cyan ink temperature does not decrease. 2136 Magenta ink temperature does not decrease. 2137 Yellow ink temperature does not decrease.
Remedy: Turn OFF the printer. (Turn OFF the printer through sub power key.)