Description: There is no more ink left. Printing in progress is interrupted immediately.
Remedy: (1) Check the ink end via gTest:Sensorh of the self-diagnostic function. . Operate the lever at the end detecting element of the ink sensor assembly to check if the ink end indication changes. (At this time, the sensor for detecting the presence of cartridges is set to Yes.) If there is no response, replace the ink sensor assembly. → Sensor menu → Replacing the I/H (ink holder) assembly (2) Check the ink sensor connector for the contact conditions. . Redo the connections of the following connectors. . Junction board : J401 . J418 . Mainboard : J133 . J134 → Replacing the Junction board assembly.
Code: n10
Display: Not Original Ink
Description:
Remedy: (1) Check the ink end ID via gTest:Sensorh of the self-diagnostic function. (This is limited to when smart chips are set.) . If the type of the installed cartridge does not match the displayed type, the ink ID sensor may be damaged. → Sensor menu (2) Check the ink ID sensor connector for the contact conditions. . Redo the connections of the following connectors : . Junction board : J401 . J418 . Mainboard : J133 . J134 → Replacing the JUNCTION board assembly. (3) The Mainboard may be damaged. . Replace the Mainboard assembly. → Replacing the Mainboard assembly, HDD_Extension board assembly, HEAD_DRV board assembly and cooling fan assembly.
Code: n11
Display: Warning Waste INK Tank
Description: The waste tank will soon be full.
Remedy: (1) Check if the message is still displayed after turning the power off and then back on again. • When a message is displayed : Go to step (2) - (2) The amount of waste ink inside the tank reached the specified level. • Dispose of the waste ink in the waste bottle. (3) If initialization does take effect when the waste ink is disposed of and waste ink history is initialized, the Mainboard may be damaged. . Replace the Mainboard assembly. → Replacing the Mainboard assembly, HDD_Extension board assembly, HEAD_DRV board assembly and cooling fan assembly.
Code: n12
Display: Warning Waste INK Tank
Description: The service life of the ink tube will soon be reached.
Remedy: (1) Check if the message is still displayed after turning the power off and then back on again. . When a message is displayed : Go to step (2) - (2) The number of times the ink tube was used reached the maximum allowable times. . Replace the ink tube. . Initializing CR motor history. → Replacing the steel bearer, tube guide, CR tape power cable and ink tube. (3) If initialization does take effect when the CR motor history is initialized after the ink tube is replaced, the Mainboard may be damaged. . Replace the Mainboard assembly. → Replacing the Mainboard assembly, HDD_Extension board assembly, HEAD_DRV board assembly and cooling fan assembly.
Code: n13
Display: (Warning Head Life)
Description: The service life of the print head will soon be reached.
Remedy: (1) Check if the message is still displayed after turning the power off and then back on again. . When a message is displayed : refer to step (2) (2) The number of times the print head was used reached the maximum allowable times. . Replace the print head assembly. . Initialize the head unit. → Replacing the print head assembly and head tape power cable. → Counter initialization menu. (3) If initialization does not take effect when the head unit is initialized, the Mainboard assembly may be damaged. . Replace the Mainboard assembly. → Replacing the Mainboard assembly, HDD_Extension board assembly, HEAD_DRV board assembly and cooling fan assembly
Code: n14
Display: Hard disk status conect error
Description: There is a problem in the hard disk connections.
Remedy: (1) Check the connections of connectors. • Redo the connections of the following connectors. • Mainboard : J102 • power source board (small) assembly : CN51 – CN52 2) The HDD_MOTHER board assembly may be damaged. . Replace the ink tube. . Initializing CR motor history. (3) Hard disk may be damaged. . Replace the hard disks. 11 Hard disk status conect error There is a problem in the hard disk connections. (4) The Mainboard assembly may be damaged. . Replace the Mainboard assembly. → Replacing the Mainboard assembly, HDD_Extension board assembly, HEAD_DRV board assembly and cooling fan assembly. → Replacing the power source board assembly.