Lexmark XC4150

• Code: 58
• Description: Too many flash options or trays.
• Remedy: Step 1 Reset the printer, and then resend the print job. Does the problem remain? Go to step 2. The problem is solved. Step 2 If applicable, make sure that the internal option is supported. Does the problem remain? Go to step 3. The problem is solved. Step 3 a If applicable, remove all internal options. b Reset the printer, and then resend the print job. Does the problem remain? Go to step 6. Go to step 4. Step 4 Check if the number of internal options installed is allowed, and remove the excess option. Does the problem remain? Go to step 5. The problem is solved. Step 5 Check if the number of input options installed is allowed, and remove the excess option. Does the problem remain? Go to step 6. The problem is solved.

• Code: 59
• Description: Incompatible option or tray.
• Remedy: Step 1 Warning—Potential Damage: Do not perform this step if the printer is on. a Reseat the hardware option cables. b Check the cables for damage, and replace if necessary. Does the problem remain? Go to step 2. The problem is solved. Step 2 Check the firmware version of the hardware option if it is supported by the engine firmware. Update the firmware if necessary. Note: Contact the next level of support for the correct firmware version. Does the problem remain? Go to step 3. The problem is solved. Step 3 Check the hardware option controller board pins for damage, and replace if necessary. Does the problem remain? Contact the next level of support. The problem is solved.

• Code: 61, 62
• Description: 61 Defective hard disk. 62 Hard disk is full.
• Remedy: Step 1 Delete unnecessary files: . Navigate to Settings > Device > Maintenance > Out.of.Service Erase > Erase Hard Disk > Sanitize all information on hard disk > Erase downloads > Delete now. . Navigate to Settings > Maintenance > Configuration Menu > Disk Configuration > Jobs on Disk > Delete. Does the problem remain? Go to step 2. The problem is solved.

• Code: 63
• Description: Unformatted hard disk.
• Remedy: Format the hard disk.

• Code: 64
• Description: Unsupported hard disk format.
• Remedy: Format the hard disk.

• Code: 647
• Description: 647.80 The motor (deskew) did not turn on. 647.81 The motor (deskew) did not turn off. 647.82 The motor (deskew) speed did not ramp up to the required level. 647.83 The motor (deskew) stalled. 647.84 The motor (deskew) ran too slow. 647.85 The motor (deskew) ran too fast. 647.86 The motor (deskew) did not run at the correct timing.
• Remedy: Step 1 Reset the printer. Does the problem remain? Go to step 2. The problem is solved. Step 2 a Enter the Diagnostics menu, and then navigate to: Printer diagnostics & adjustments > Motor tests > Deskew b Touch Start. Does the motor run? Go to step 3. Go to step 5. Step 3 Turn the aligner and registration rollers. Is there binding or uneven movement when turning the rollers? Go to step 4. Go to step 5. Step 4 Check the aligner roller gears for damage, and replace if necessary. Does the problem remain? Go to step 5. The problem is solved. Step 5 Check the cable on the motor and on the JMTR1 connector on the controller board for proper connection. Is the cable properly connected at both ends? Go to step 7. Go to step 6. Step 6 Reconnect the cable. Does the problem remain? Go to step 7. The problem is solved. Step 7 Check the cable for damage, and replace if necessary. Does the problem remain? Go to step 8. The problem is solved. Step 8 Replace the motor. See “Motor (deskew) removal”. Does the problem remain? Go to step 9. The problem is solved. Step 9 Replace the controller board. See “Controller board removal”. Does the problem remain? Contact the next level of support. The problem is solved.