PrintCopy.info service

Lexmark C544n

Error Codes List page 2

  • Code: 106.07
  • Description: Service Yellow Printhead
    The yellow printhead thermistor isshorted to ground.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
  • Code: 106.08
  • Description: Service Yellow Printhead
    The yellow laser showed bad in testing.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
  • Code: 106.09
  • Description: Service Yellow Printhead
    SOS/EOS measurement did not complete.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
  • Code: 106.10
  • Description: Service Yellow Printhead
    Bad SOS/EOS measurement.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
  • Code: 106.11
  • Description: Service Yellow Printhead
    Failure writing data tot he printhead.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
  • Code: 106.12
  • Description: Service Yellow Printhead
    Failure reading data from the printhead.
  • Remedy: 1 Turn the printer off, and remove the rear shield. See “Rear shield removal”. Check the cable at JMIRR1 for proper connection to the controller board, the printhead cable for pinch points, and the cable or connector for any other damage. Is the cable damaged? Replace the printhead. See “Printhead removal”. Go to step 2.
    2 Turn the printer on, and then wait until the printer posts an error. Using a voltmeter, check the following values at JMIRR1: Are the values approximately correct? Replace the controller board See “Controller board removal”. Replace the printhead. See “Printhead removal”.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us