PrintCopy.info service

Lexmark C534dn

Error Codes List page 2

  • Code: 120-03
  • Description: Fuser Error
    An error has occurred in the fuser.
  • Remedy: 1 Check the input voltage switch on the back of the low volt power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set switch for proper country voltage.
    2 Turn the printer off and remove the rear cover. Check connector JFUSER1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go step 3. If connector is damaged on system card, replace system card. Go to “System card removal”. If fuser cable is damaged, replace cable.
    3 Check connector JLVPS1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go step 4. If connector is damaged on system card, replace system card. Go to “System card removal”. If LVPS cable is damaged, replace LVPS. Go to “Low volt power supply (LVPS) removal”.
    4 Replace fuser. Go to “Fuser removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
  • Code: 120-04...120-07
  • Description: Fuser Error
    An error has occurred in the fuser.
  • Remedy: 1 Check the input voltage switch on the back of the low volt power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set switch for proper country voltage.
    2 Turn the printer off and remove the rear cover. Check connector JFUSER1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go step 3. If connector is damaged on system card, replace system card. Go to “System card removal”. If fuser cable is damaged, replace cable.
    3 Remove fuser. Go to “Fuser removal”. Check AC and DC auto-connects on both the fuser and the printer for damage. Are connectors free of damage? Go to step 4. If connector is damaged on fuser, replace fuser. If either of the cable connectors are damaged, replace the appropriate cable.
    4 Check for the following continuity between DC auto-connect and FUSER1. Is continuity present? DC auto-connect JFUSER1 pin 9 pin 9 pin 10 pin 10 Go to step 5. Replace DC fuser cable.
    5 Check for continuity between the following pins of the AC auto-connect and the pins of the connector that connects to the LVPS. Is continuity present? LVPS connector AC auto-connect pin 1 pin 5 pin 2 pin 4 pin 3 pin 1 Go to step 6. Replace AC fuser cable.
    6 Reinstall fuser. Go to “Fuser removal”. Does error clear? Problem solved. Go to step 7.
    7 Replace fuser. Go to “Fuser removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
  • Code: 120-10, 120-13, 120-14, 120-15
  • Description: Fuser Error
    An error has occurred in the fuser.
  • Remedy: 1 Check the input voltage switch on the back of the low volt power supply (LVPS). Is the voltage level (115/230) properly set? Go to step 2. Set switch for proper country voltage.
    2 Turn the printer off and remove the rear cover. Check connector JFUSER1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go step 3. If connector is damaged on system card, replace system card. Go to “System card removal”. If fuser cable is damaged, replace cable.
    3 Check connector JLVPS1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go step 4. If connector is damaged on system card, replace system card. Go to “System card removal”. If LVPS cable is damaged, replace LVPS. Go to “Low volt power supply (LVPS) removal”.
    4 Remove fuser. Go to “Fuser removal”. Check AC and DC auto-connects on both the fuser and the printer for damage. Are connectors free of damage? Go to step 5. If connector is damaged on fuser, replace fuser. If either of the cable connectors are damaged, replace the appropriate cable.
    5 Check for the following continuity between DC auto-connect and FUSER1. Is continuity present? DC auto-connect JFUSER1 pin 9 pin 9 pin 10 pin 10 Go to step 6. Replace DC fuser cable.
    6 Check for continuity between the following pins of the AC auto-connect and the pins of the connector that connects to the LVPS. Is continuity present? LVPS connector AC auto-connect pin 1 pin 5 pin 2 pin 4 pin 3 pin 1 Go to step 7. Replace AC fuser cable.
    7 Reinstall fuser. Go to “Fuser removal”. Does error clear? Problem solved. Go to step 8.
    8 Replace fuser. Go to “Fuser removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
  • Code: 140-01, 140-03...140-08
  • Description: Autocomp Motor Error
    Tray 1 motor has failed.
  • Remedy: 1 Turn the printer off and remove the rear cover. Check connector JTRAY2 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go to “Network system card” for fuse location on the network system card. Go to “Parallel system card” for fuse location on the network system card. Go to step 2. If connector is damaged on system card, replace system card. Go to “System card removal”. If JTRAY2 cable is damaged, replace paper pick mechanism. Go to “Paper pick mechanism assembly removal”.
    2 Measure the resistance across fuser F2 on the system card. Is fuser blown? Go to “Network system card”. Replace system card. Go to “System card removal”. Go to step 3.
    3 Replace paper pick mechanism. Go to “Paper pick mechanism assembly removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
  • Code: 140-02
  • Description: Autocomp Motor Error
    Tray 1 motor has failed.
  • Remedy: 1 Turn the printer off and remove the rear cover. Check connector JTRAY2 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go to step 2. If connector is damaged on system card, replace system card. Go to “System card removal”. If JTRAY2 cable is damaged, replace paper pick mechanism. Go to “Paper pick mechanism assembly removal”.
    2 Replace paper pick mechanism. Go to “Paper pick mechanism assembly removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
  • Code: 142-xx
  • Description: Motor Error
    Fuser motor has failed.
  • Remedy: 1 Turn the printer off and remove the rear cover. Check connector JFUSER1 for proper connection to system card, cable for pinch points and cable or connector for any other damage. Is cable properly connected and damage free? Go to step 2. If connector is damaged on system card, replace system card. Go to “System card removal”. If fuser cable is damaged, replace cable.
    2 Turn printer power on and check for 24 V dc between JCVR1 pin 1 (red wire) and ground. Is voltage present? Note: Ground lead of voltmeter can be placed on metal chasis to obtain ground. Go to step 3. Disconnect JCVR1 and check for 24 V dc between pin 1 of system card connector and ground. If voltage is present, replace 24V interlock switch.Go to “Top access door 24V interlock switch removal”. If voltage is not present, replace system card. Go to “System card removal”.
    3 Reconnect JCVR1 if disconnected. Ensure top access door is completely closed. Check for 24 V dc between JCVR1 pin 2 (white wire) and ground. Is voltage present? Go to step 4. Replace 24V interlock switch. Go to “Top access door 24V interlock switch removal”
    4 Replace fuser. Go to “Fuser removal”. Does error clear? Problem solved. Replace system card. Go to “System card removal”.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us