PrintCopy.info service

Konica-Minolta bizhub C360i

Error Codes List page 2

  • Code: 15-01, 15-40
  • Description: Misfeed at external LCT paper feed section
    15-01 The leading edge of the paper is not turned ON the LU paper feed sensor (PS3) even after the lapse of a given period of time after the external LCT starts to feed paper.
    15-40 For paper fed from the external LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the external LCT paper feed section results, if the LU paper feed sensor (PS3) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the external LCT paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • LU paper feed motor (M2) • LU paper feed sensor (PS3) • LU drive board (LUDB) • Base board (BASEB) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 Make the pick-up roller load adjustment of the LCT. - - 3 PS3 I/O check, sensor check LUDB CN5-8 (ON) LU-302 4-G 4 M2 load check • Check code: 28 • Multi code: 41, 44, 45 LUDB CN4-5 to 8 LU-302 3-G 5 Replace LUDB. - - 6 Replace BASEB. - - 7 Replace PCCB. (PC-116/PC-216 / PC-416)
  • Code: 16-01, 16-05, 16-40
  • Description: Misfeed at transfer LCT paper feed/transport section
    16-01 After the transfer LCT starts to feed paper, the vertical transport sensor (PS133) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the paper feed sensor (PS132).
    16-05 The leading edge of the paper is not turned ON the paper feed sensor (PS132) even after the lapse of a given period of time after the transfer LCT starts to feed paper.
    16-40 For paper fed from the transfer LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the transfer LCT transport section results, if the vertical transport sensor (PS133) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the transfer LCT transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Paper feed motor (M131) • Vertical transport motor (M132) • Paper feed sensor (PS132) • Vertical transport sensor (PS133) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 PS132 I/O check, sensor check PCCB CN4-11 (ON) PC-416 7-J 3 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-416 7-J 4 M131 load check • Check code: 28 • Multi code: 1, 4, 5 PCCB CN5-1 to 8 PC-416 5-J 5 M132 load check • Check code: 28 • Multi code: 6, 9, 10 PCCB CN5-9 to 16 PC-416 4-J 6 Replace PCCB.
  • Code: 20-01, 20-02
  • Description: Misfeed at vertical transport section
    20-01 The registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 2 vertical transport sensor (PS19).
    20-02 For paper fed from the tray 2, tray 3, tray 4, or LCT, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
  • Causes: • Transport motor (M1) • Tray 2 vertical transport clutch (CL2) • Registration clutch (CL4) • Registration sensor (PS1) • Tray 2 vertical transport sensor (PS19) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C 3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K 4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K 5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C 6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 7 Replace BASEB.
  • Code: 20-21
  • Description: Misfeed at vertical transport section (tray 3)
    <When PC-116 or PC-216 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 3 vertical transport sensor (PS113).
    <When PC-416 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the vertical transport sensor (PS133).
    Paper jam of a sheet of paper left at the vertical transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: <When PC-116 or PC-216 is installed> • Transport motor (M1) • Tray 3 vertical transport motor (M112) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • Tray 3 vertical transport sensor (PS113) • Base board (BASEB) • PC control board (PCCB)
    <When PC-416 is installed> • Transport motor (M1) • Vertical transport motor (M132) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • Vertical transport sensor (PS133) • Base board (BASEB) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-116/PC-216 5-C 3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K 4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K 5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-116/PC-216 3 to 4-C 6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 7 Replace BASEB. - - 8 Replace PCCB.
    When PC-416 is installed 1 Initial check items - - 2 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-416 7-J 3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K 4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K 5 M132 load check • Check code: 28 • Multi code: 6, 9, 10 PCCB CN5-9 to 16 PC-416 4-J 6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 7 Replace BASEB. - - 8 Replace PCCB.
  • Code: 20-22
  • Description: Misfeed at vertical transport section (tray 4)
    20-22 The tray 3 vertical transport sensor (PS113) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 4 vertical transport sensor (PS123).
    - Paper jam of a sheet of paper left at the vertical transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Tray 3 vertical transport motor (M112) • Tray 4 vertical transport motor (M122) • Tray 3 vertical transport sensor (PS113) • Tray 4 vertical transport sensor (PS123) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 PS123 I/O check, sensor check PCCB CN18-5 (ON) PC-216 7-K 3 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-216 5-C 4 M122 load check • Check code: 28 • Multi code: 26, 29, 30 PCCB CN9C-9 to 16 PC-216 6-K 5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-216 3 to 4-C 6 Replace PCCB.
  • Code: 30-03
  • Description: Misfeed at 2nd transfer section
    30-03 The fusing loop sensor (PS2) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (unblocked) the registration sensor (PS1).
    - Paper jam of a sheet of paper left at the 2nd transfer section results, if the registration sensor (PS1) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the 2nd transfer section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Transport motor (M1) • Registration clutch (CL4) • Registration sensor (PS1) • Fusing loop sensor (PS2) • Expansion control board (EXCB) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C 3 PS2 I/O check, sensor check EXCB CN13EX-6 (ON) 4-X 4 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C 5 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 6 Replace EXCB. - - 7 Replace BASEB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us