Konica-Minolta bizhub C3350i
Error Codes List page 3
|
|
- Code: 66-13, 66-33
- Description: Misfeed at DF document transport section
66-13 The document registration sensor (PS17) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the after separate sensor (PS16). 66-33 The document before read sensor (PS18) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON (unblocked) the document registration sensor (PS17). - Paper jam of a sheet of paper left at the DF document transport section results, if the document registration sensor (PS17) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Document main motor (M8) • Document paper feed clutch (CL8) • Document registration clutch (CL9) • After separate sensor (PS16) • Document registration sensor (PS17) • Document before read sensor (PS18) • DF control board (DFCB)
- Remedy: 1 Initial check items - - 2 PS16 I/O check, sensor check DFCB CN3-2 (ON) 21-P 3 PS17 I/O check, sensor check DFCB CN2-8 (ON) 23-P 4 PS18 I/O check, sensor check DFCB CN6-2 (ON) 21-P 5 CL8 load check • Check code: 60 • Multi code: 145 DFCB CN4-2 (ON) 21-X 6 CL9 load check • Check code: 60 • Multi code: 146 DFCB CN4-4 (ON) 21-X 7 M8 load check • Check code: 60 • Multi code: 1, 5 DFCB CN5-1 to 4 21-X 8 Replace DFCB.
- Code: 92-01, 92-02
- Description: Misfeed at duplex pre-registration section
92-01 The leading edge of the paper is not turned ON (blocked) the registration sensor (PS9) even after the lapse of a given period of time after a duplex paper feed sequence has been started. 92-02 After the start of the second-side feed of paper in the duplex mode, loop forming has not been complete before the second side of a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop. - Paper jam of a sheet of paper left at the duplex pre-registration section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Main motor (M1) • Registration clutch (CL4) • ADU transport clutch (CL5) • Registration sensor (PS9) • ADU transport sensor (PS11) • Base board (BASEB)
- Remedy: 1 Initial check items - - 2 PS9 I/O check, sensor check BASEB CN22EA-13 (ON) 13-C 3 PS11 I/O check, sensor check BASEB CN23E-6 (ON) 9-K 4 CL4 load check • Check code: 21 • Multi code: 3 BASEB CN22EA-3 (ON) 12-C 5 CL5 load check • Check code: 81 BASEB CN23E-12 (ON) 9-K • Multi code: 1 6 M1 load check • Check code: 40 • Multi code: 1, 2 BASEB CN17E-1 to 5 1-C 7 Replace BASEB.
- Code: 92-03, 92-04
- Description: Misfeed at duplex pre-registration section.
92-03 For the second-side feed of paper in the duplex mode, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. 92-04 The leading edge of the paper is not turned OFF (blocked) the ADU transport sensor (PS11) even after the lapse of a given period of time after a duplex paper feed sequence has been started. - Paper jam of a sheet of paper left at the duplex pre-registration section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Main motor (M1) • Registration clutch (CL4) • ADU transport clutch (CL5) • Registration sensor (PS9) • ADU transport sensor (PS11) • Base board (BASEB)
- Remedy: 1 Initial check items - - 2 PS9 I/O check, sensor check BASEB CN22EA-13 (ON) 13-C 3 PS11 I/O check, sensor check BASEB CN23E-6 (ON) 9-K 4 CL4 load check • Check code: 21 • Multi code: 3 BASEB CN22EA-3 (ON) 12-C 5 CL5 load check • Check code: 81 BASEB CN23E-12 (ON) 9-K • Multi code: 1 6 M1 load check • Check code: 40 • Multi code: 1, 2 BASEB CN17E-1 to 5 1-C 7 Replace BASEB.
- Code: 93-03
- Description: Misfeed at duplex transport section
93-03 The leading edge of the paper is not turned ON (unblocked) the ADU transport sensor (PS11) even after the lapse of a given period of time after the paper has turned OFF (blocked) the paper exit sensor (PS13). - Paper jam of a sheet of paper left at the duplex transport section results, if the ADU transport sensor (PS11) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Paper jam of a sheet of paper left at the duplex transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Main motor (M1) • Fusing motor (M3) • ADU transport clutch (CL5) • ADU forward rotation clutch (CL6) • ADU reverse rotation clutch (CL7) • ADU transport sensor (PS11) • Paper exit sensor (PS13) • Base board (BASEB)
- Remedy: 1 Initial check items - - 2 PS11 I/O check, sensor check BASEB CN23E-6 (ON) 9-K 3 PS13 I/O check, sensor check BASEB CN16E-3 (ON) 11-K 4 CL5 load check • Check code: 81 • Multi code: 1 BASEB CN23E-12 (ON) 9-K 5 CL6 load check • Check code: 80 • Multi code: 1 BASEB CN18E-6 (ON) 2-C 6 CL7 load check • Check code: 80 • Multi code: 2 BASEB CN18E-8 (ON) 3-C 7 M1 load check • Check code: 40 • Multi code: 1, 2 BASEB CN17E-1 to 5 1-C 8 M3 load check • Check code: 45 • Multi code: 1, 2, 3 BASEB CN17E-6 to 10 1-C 9 Replace BASEB.
- Code: 99-01
- Description: Controller JAM (paper size error)
99-01 • As a result of a paper size error, the controller transmits a forced stop command to the printer engine and the printer engine is internally processing the size error. • As a result of a paper size error, the controller transmits a forced stop command to the printer engine; but the paper causing the size error cannot be fed out. - Causes:
- Remedy: 1 Initial check items - - 2 Open and close the front door of the main body.
- Code: 99-02
- Description: Controller JAM (controller forced stop command)
99-02 The controller transmits a forced stop command under a condition other than a paper size error during a print cycle. - Causes:
- Remedy: 1 Initial check items - - 2 Open and close the front door of the main body.