PrintCopy.info service

Konica-Minolta bizhub C227i

Error Codes List page 1

  • Code: 10-01, 10-02, 10-40
  • Description: Misfeed at manual bypass paper feed section
    10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
    10-02 For paper fed from the manual bypass tray, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
    10-40 For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
  • Causes: • Transport motor (M1)
    • Registration clutch (CL4)
    • Bypass tray paper feed clutch (CL7)
    • Registration sensor (PS1)
    • Base board (BASEB)
  • Remedy: 1 Initial check items - -
    2 PS1 I/O check, sensor check BASEB CN13E<A>-9 (ON) 6-C
    3 CL4 load check
    • Check code: 21
    • Multi code: 2
    BASEB CN13E<A>-11 (ON) 7-C
    4 CL7 load check
    • Check code: 20
    • Multi code: 3
    BASEB CN30E-2 (ON) 13-C
    5 M1 load check
    • Check code: 40
    • Multi code: 1, 3
    BASEB CN11E-4 (REM)
    BASEB CN11E-7 (LOCK)
    3-C
    6 BASEB F13E, F21E conduction check - -
    7 Replace BASEB.
  • Code: 11-01, 11-02, 11-05, 11-40
  • Description: Misfeed at tray 1 paper feed section
    11-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper.
    11-02 For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the transport motor (M1).
    11-05 The leading edge of the paper is not turned ON the tray 1 paper feed sensor (PS23) even after the lapse of a given period of time after the tray 1 starts to feed paper.
    11-40 For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
  • Causes: • Transport motor (M1)
    • Tray 1 paper feed clutch (CL3)
    • Registration clutch (CL4)
    • Registration sensor (PS1)
    • Tray 1 paper feed sensor (PS23)
    • Base board (BASEB)
  • Remedy: 1 Initial check items - -
    2 PS1 I/O check, sensor check BASEB CN13E<A>-9 (ON) 6-C
    3 PS23 I/O check, sensor check BASEB CN5E<A>-3 (ON) 9-C
    4 CL3 load check
    • Check code: 20
    • Multi code: 1
    BASEB CN5E<A>-11 (ON) 9-C
    5 CL4 load check
    • Check code: 21
    • Multi code: 2
    BASEB CN13E<A>-11 7-C
    6 M1 load check
    • Check code: 40
    • Multi code: 1, 3
    BASEB CN11E-4 (REM)
    BASEB CN11E-7 (LOCK)
    3-C
    7 BASEB F13E, F21E conduction check - -
    8 Replace BASEB. - -
  • Code: 12-01, 12-05, 12-40
  • Description: Misfeed at tray 2 paper feed section
    12-01 The leading edge of the paper is not turned ON (unblocked) the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper.
    12-05 The leading edge of the paper is not turned ON the tray 2 paper feed sensor (PS20) even after the lapse of a given period of time after the tray 2 starts to feed paper.
    12-40 For paper fed from the tray 2, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 2 feed section results, if the tray 2 vertical transport sensor (PS19) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 2 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Transport motor (M1)
    • Tray 2 paper feed clutch (CL1)
    • Tray 2 vertical transport clutch (CL2)
    • Tray 2 vertical transport sensor (PS19)
    • Tray 2 paper feed sensor (PS20)
    • Base board (BASEB)
  • Remedy: 1 Initial check items - -
    2 PS19 I/O check, sensor check BASEB CN5E<B>-16 (ON) 12-C
    3 PS20 I/O check, sensor check BASEB CN5E<B>-3 (ON) 10-C
    4 CL1 load check
    • Check code: 20
    • Multi code: 2
    BASEB CN5E<B>-11 (ON) 11-C
    5 CL2 load check
    • Check code: 21
    • Multi code: 1
    BASEB CN5E<B>-13 (ON) 11-C
    6 M1 load check
    • Check code: 40
    • Multi code: 1, 3
    BASEB CN11E-4 (REM)
    BASEB CN11E-7 (LOCK)
    3-C
    7 BASEB F13E, F21E conduction check - -
    8 Replace BASEB.
  • Code: 13-01, 13-05, 13-40
  • Description: Misfeed at tray 3 paper feed section
    13-01 The leading edge of the paper is not turned ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper.
    13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS112) even after the lapse of a given period of time after the tray 3 starts to feed paper.
    13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 3 feed section results, if the tray 3 vertical transport sensor (PS113) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 3 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Tray 3 paper feed motor (M111)
    • Tray 3 vertical transport motor (M112)
    • Tray 3 paper feed sensor (PS112)
    • Tray 3 vertical transport sensor (PS113)
    • PC control board (PCCB)
  • Remedy: 1 Initial check items - -
    2 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-118/PC-218 5-C
    3 PS112 I/O check, sensor check PCCB CN4-11 (ON) PC-118/PC-218 5-C
    4 M111 load check
    • Check code: 28
    • Multi code: 9, 11
    PCCB CN5-1 to 8 PC-118/PC-218 4-C
    5 M112 load check
    • Check code: 28
    • Multi code: 17, 19
    PCCB CN5-9 to 16 PC-118/PC-218 3 to 4-C
    6 Replace PCCB.
  • Code: 14-01, 14-05, 14-40
  • Description: Misfeed at tray 4 paper feed section
    14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper.
    14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS122) even after the lapse of a given period of time after the tray 4 starts to feed paper.
    14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 4 feed section results, if the tray 4 vertical transport sensor (PS123) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 4 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Tray 4 paper feed motor (M121)
    • Tray 4 vertical transport motor (M122)
    • Tray 4 paper feed sensor (PS122)
    • Tray 4 vertical transport sensor (PS123)
    • PC control board (PCCB)
  • Remedy: 1 Initial check items - -
    2 PS123 I/O check, sensor check PCCB CN18C-5 (ON) PC-218 7-K
    3 PS122 I/O check, sensor check PCCB CN18C-2 (ON) PC-218 7-K
    4 M121 load check
    • Check code: 28
    • Multi code: 13, 15
    PCCB CN9C-1 to 8 PC-218 6-K
    5 M122 load check
    • Check code: 28
    • Multi code: 21, 23
    PCCB CN9C-9 to 16 PC-218 6-K
    6 Replace PCCB.
  • Code: 16-01, 16-05, 16-40
  • Description: Misfeed at LCT feed/vertical transport section
    16-01 The leading edge of the paper is not turned ON the LCT vertical transport sensor (PS133) even after the lapse of a given period of time after the LCT starts to feed paper.
    16-05 The leading edge of the paper is not turned ON the paper feed sensor (PS132) even after the lapse of a given period of time after the LCT starts to feed paper.
    16-40 For paper fed from the LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the LCT transport section results, if the LCT vertical transport sensor (PS133) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the LCT transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Paper feed motor (M131)
    • Vertical transport motor (M132)
    • Paper feed sensor (PS132)
    • LCT vertical transport sensor (PS133)
    • PC control board (PCCB)
  • Remedy: 1 Initial check items - -
    2 PS132 I/O check, sensor check PCCB CN4-11 (ON) PC-418 7-J
    3 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-418 7-J
    4 M131 load check
    • Check code: 28
    • Multi code: 1, 3
    PCCB CN5-1 to 8 PC-418 5-J
    5 M132 load check
    • Check code: 28
    • Multi code: 5, 7
    PCCB CN5-9 to 16 PC-418 4-J
    6 Replace PCCB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Home
New Register Forgot Password?
Send message to us