Konica-Minolta bizhub 227
Error Codes List page 2
|
|
- Code: C0204
- Description: Tray 2 feeder up/down abnormality The tray 2 upper limit sensor (PS25) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
- Causes: • Tray 2 lift-up motor (M13) • Tray 2 upper limit sensor (PS25) • MFP board (MFPB)
- Remedy: 1. Check the connector between M13-MFPB CN8E for proper connection and correct as necessary. 2. Check the connector of M13 for proper drive coupling and correct as necessary. 3. Check the connector between PS25-relay CN49-MFPB CN11 for proper connection and correct as necessary. 4. PS25 I/O check, sensor check • Control signal: MFPB CN11E-13 (ON) • Location of electrical component: 6-C 5. M13 operation check • Control signal: MFPB MFPB CN8E-1 to 2 • Location of electrical component: 10-C 6. Replace M13. 7. MFPB F5E conduction check 8. Replace MFPB. NOTICE • Link to the wiring diagram (N.1. bizhub 367/287/227)
- Code: C0206
- Description: Tray 3 lift-up failure (When PC-113 or PC-213 is installed) The tray 3 upper limit sensor (PS116) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
- Causes: • Tray 3 lift-up motor (M113) • Tray 3 upper limit sensor (PS116) • PC control board (PCCB) • MFP board (MFPB)
- Remedy: 1. Check the connector between M113-PCCB CN6 for proper connection and correct as necessary. 2. Check the connector of M113 for proper drive coupling and correct as necessary. 3. Check the connector between PS116-relay CN24-PCCB CN4 for proper connection and correct as necessary. 4. PS116 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-113/PC-213 7-C 5. M113 operation check • Control signal: PCCB CN6-8 to 9 • Location of electrical component: PC-113/PC-213 2-C 6. Replace M113. 7. Replace PCCB. 8. MFPB F4E conduction check 9. Replace MFPB. NOTICE • Link to the wiring diagram (N.2.2 PC-113) • Link to the wiring diagram (N.2.3 PC-213)
- Code: C0208
- Description: Tray 4 lift-up failure (When PC-213 is installed) The tray 4 upper limit sensor (PS126) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
- Causes: • Tray 4 lift-up motor (M123) • Tray 4 upper limit sensor (PS126) • PC control board (PCCB) • MFP board (MFPB)
- Remedy: 1. Check the connector between M123-PCCB CN8 for proper connection and correct as necessary. 2. Check the connector of M123 for proper drive coupling and correct as necessary. 3. Check the connector between PS126-relay CN47-PCCB CN7 for proper connection and correct as necessary. 4. PS126 I/O check, sensor check • Control signal: PCCB CN7-3 (ON) • Location of electrical component: PC-213 8-K 5. M123 operation check • Control signal: PCCB CN8-8 to 9 • Location of electrical component: PC-213 5-K 6. Replace M123. 7. Replace PCCB. 8. MFPB F4E conduction check 9. Replace MFPB. NOTICE • Link to the wiring diagram (N.2.3 PC-213)
- Code: C0210
- Description: LCT lift failure (When PC-413 is installed) • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The shifter stop / lower limit position sensor (PS138) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began. • The main tray upper limit sensor (PS136) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operating. • The main tray upper limit sensor (PS136) is not turned OFF (unblocked) even after the set period of time has elapsed after the paper lift-down operation began. • The shifter stop / lower limit position sensor (PS138) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-down operation began.
- Causes: • Elevator motor (M134) • Main tray upper limit sensor (PS136) • Shifter stop / lower limit position sensor (PS138) • PC control board (PCCB) • MFP board (MFPB)
- Remedy: 1. Check the connector between M134-PCCB CN10 for proper connection and correct as necessary. 2. Check the connector of M134 for proper drive coupling and correct as necessary. 3. Check the connector between PS136-relay CN1-PCCB CN4 for proper connection and correct as necessary. 4. Check the connector between PS138-relay CN16-PCCB CN14 for proper connection and correct as necessary. 5. PS136 I/O check, sensor check • Control signal: PCCB CN4-3 (ON) • Location of electrical component: PC-413 8-J 6. PS138 I/O check, sensor check • Control signal: PCCB CN14-6 (ON) • Location of electrical component: PC-413 4-J 7. M134 operation check • Control signal: PCCB CN10-1 to 2 • Location of electrical component: PC-413 6-J 8. Replace M134. 9. Replace PCCB. 10. MFPB F4E conduction check 11. Replace MFPB.
- Code: C0211
- Description: Manual feed up/down abnormality • Paper is not turned OFF (unblock) the bypass tray position sensor (PS28) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position. • The bypass tray position sensor (PS28) is not turned ON (blocked) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-up plate to the feed position
- Causes: • Transport motor (M1) • Bypass pick-up solenoid (SD1) • Bypass tray position sensor (PS28) • MFP board (MFPB)
- Remedy: 1. Check the connector between M1-MFPB CN19E for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN91 (bizhub 367), CN34 (bizhub 287), CN90 (bizhub 227)-MFPB CN9 for proper connection and correct as necessary. 4. SD1-relay CN41- relay CN91 (bizhub 367), CN34 (bizhub 287), CN90 (bizhub 227)-MFPB CN9E for proper connection and correct as necessary. 5. PS28 I/O check, sensor check • Control signal: MFPB CN9E-3 (ON) • Location of electrical component: 3-J 6. SD1 operation check • Control signal: MFPB CN9E-12 (ON) • Location of electrical component: 4-J 7. M1 operation check • Control signal: MFPB CN19E-3 to 7 • Location of electrical component: 26-C 8. Replace M1. 9. MFPB F5E conduction check 10. Replace MFPB.
- Code: C0214
- Description: LCT shift failure (When PC-413 is installed) • The shifter stop / lower limit position sensor (PS138) is not turned ON (blocked) even after the set period of time has elapsed after the shift operation began (shift to the right). • The shifter home sensor (PS139) is not turned OFF (unblocked) even after the set period of time has elapsed after the shift operation began (shift to the right). • The shifter stop / lower limit position sensor (PS138) is not turned OFF (unblocked) even after the set period of time has elapsed after the return operation began (shift to the left). • The shifter home sensor (PS139) is not turned ON (blocked) even after the set period of time has elapsed after the return operation began (shift to the left).
- Causes: • Shifter motor (M133) • Shifter stop / lower limit position sensor (PS138) • Shifter home sensor (PS139) • PC control board (PCCB)
- Remedy: 1. Check the connector between M133-PCCB CN10 for proper connection and correct as necessary. 2. Check the connector of M133 for proper drive coupling and correct as necessary. 3. Check the connector between PS138-relay CN16-PCCB CN14 for proper connection and correct as necessary. 4. Check the connector between PS139-relay CN16-PCCB CN14 for proper connection and correct as necessary. 5. PS138 I/O check, sensor check • Control signal: PCCB CN14-6 (ON) • Location of electrical component: PC-413 4-J 6. PS139 I/O check, sensor check • Control signal: PCCB CN14-3 (ON) • Location of electrical component: PC-413 4-J 7. M133 operation check • Control signal: PCCB CN10-3 to 4 • Location of electrical component: PC-413 6-J 8. Replace M133. 9. Replace PCCB.