PrintCopy.info service

KIP K57

Error Codes List page 1

  • Code: -cut-
  • Description: Initial Cut Paper Jam
  • Causes: Initial Cut Paper is remained in the Printer.
  • Remedy:
  • Code: ct
  • Description: During Toner Checking
  • Causes: The machine is taking a Diagnosis of itself after toner supplying. Wait for about 2 minutes.
  • Remedy:
  • Code: do1
  • Description: Door Open 1
  • Causes: The Upper Roll Deck is not locked.
  • Remedy: 1) Push the Upper Roll deck into the machine a little strongly, and check whether it is locked firmly or not. 2) Check whether the Cutter Hatch is opened or not, and whether the Micro Switch is firmly pressed or not. 3) Check whether the power of 24V is supplied or not to the connector J1-1 on the Main PCB. If it is supplied, replace the Main PCB. If it is not, check whether the Micro Switch of the Upper Roll Deck surely touches the Cutter Hatch or not. 4) Especially check whether the Drawer Connector is firmly connected or not, which connects the Roll Deck to the machine when the deck is closed, since defective connection will often occur.
  • Code: do2
  • Description: Door Open 2
  • Causes: The Lower Roll Deck is not locked.
  • Remedy: 1) Push the Lower Roll Deck into the machine a little strongly, and check whether it is locked firmly or not. 2) Check whether the Cutter Hatch is opened or not, and whether the Micro Switch is firmly pressed or not. 3) Check whether the power of 24V is supplied or not to the connector J1-1 on the Main PCB. If it is supplied, replace the Main PCB. If it is not, check whether the Micro Switch of the Lower Roll Deck surely touches the Cutter Hatch or not. 4) Especially check whether the Drawer Connector is firmly connected or not, which connects the Roll Deck to the machine when the deck is closed, since defective connection will often occur.
  • Code: do3
  • Description: Door Open 3
  • Causes: The Cutter Hatch is opened, or either of Upper or Lower Roll Deck is not pushed into the machine firmly.
  • Remedy: 1) Check whether the Cutter Hatch is opened or not, and whether the Micro Switch is pressed firmly or not. 2) Push both Roll Decks into the machine firmly. 3) Check whether the power of 24V is supplied or not to the connector J1-1 on the Main PCB. If it is supplied, replace the Main PCB. If it is not, check whether both Micro Switches of Upper and Lower Roll Decks surely touch the Cutter Hatch or not. 4) Especially check whether Drawer Connectors are firmly connected or not, which connect each Roll Deck to the machine when the deck is closed, since defective connection will often occur.
  • Code: E01
  • Description: Fuser (Center ) Abnormal Low Temperature
    The temperature on the center part of the Fuser Roller is fallen abnormally. The Fuser Lamp (H1 : For the center part) may be broken, or the Thermostat 1 (TS1) may be open circuited.
  • Causes: 1. The fusing temperature does not rise up to the specified level within a specified period (rise of 20 degrees centigrade within 5 minutes) since you have turned on the machine. (This will occur in such case when surrounding air is extremely cold in the less power supplying condition.) 2. The fusing temperature becomes colder than 120 degrees centigrade.
  • Remedy: 1) Turn off the machine once, then it on again. In case of “1” of the above causes, the error can be fixed by this treatment. 2) Turn off the machine and wait until the fuser is cooled enough. Then turn on the machine, and check whether the Fuser Lamp lights or not. In case the Fuser Lamp lights, you can take printing when the machine gets ready. In case it does not light, do as follows orderly. (a) Check whether the Thermostat (TS1) is having some abnormality or not. (b) Measure the voltage of each yellow and purple wire of the SSR1 (Upper). If the voltage of the yellow one is 5V and that of purple one is 0V, replace the SSR1 (Upper). (c) Check whether there is any resistance or not, between connector J12-17 on the Main PCB and the purple wire of the SSR1. If there is, replace the Main PCB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us