Causes: 1. Communication between KIP9000 and Folder is abnormal. 2. Folder has any error other than jam.
Remedy: Communication error 1 Is any error message indicated on the Operation Panel of Folder? No This is a communication error. 1. Turn off/on both KIP9000 and folder. 2. Check the cables. 3. Replace the Main Control PCB. Error of Folder 2 Is any error message indicated on the Operation Panel of Folder? Yes This is an error of Folder. Turn off/on the Folder. If the error still occurs, ask the service for the Folder.
Code: E-Fb
Description: Flash ROM Error
Causes: Writing to the Flash ROM is failed.
Remedy: Defect of Flash ROM 1 Can the error be fixed by replacing the Flash ROM? Yes OK.
Code: J-01
Description: Roll 1 Jam
Causes: 1. Roll Set Sensor 1 Signal (RP_SET1) does not change from H to L within a decided time since the KIP9000 has started transporting the Roll 1 from the wait position. 2. Roll Set Sensor 1 Signal (RP_SET1) does not change from L to H within a decided time since the KIP9000 has started retrieving the Roll 1 back to wait position.
Remedy: Roll Set Sensor 1 (PH1) 1 Check the input signal from the Roll Set Sensor 1 (signal code 04) in the Input/Output Checking Mode of Service Mode. Is it “L” when the media is on the sensor and “H” when the media is not on the sensor? No 1. Check if the sensor harness has any abnormality. 2. Replace the sensor (PH1) if the harness is OK. Roll Paper Feed Clutch 1 (MC1) Roll Deck 1 Feed Clutch (MC8) 2 Can the following clutches be operated properly in the Function Checking Mode of Service Mode? - Roll Paper Feed Clutch 1 (Signal code : 92) - Roll Deck 1 Feed Clutch (Signal code : 9C) No 1. Check if the harness of clutch has any abnormality. 2. Replace each clutch (MC1 & MC8) if the harness is OK. DC Driver PCB (PW7755) 3 Can the error be fixed by replacing the DC Driver PCB? Yes OK Main Control PCB (PW11520) 4 Can the error be fixed by replacing the Main Control PCB? Yes OK
Code: J-02
Description: Roll 2 Jam
Causes: 1. Roll Set Sensor 2 Signal (RP_SET2) does not change from H to L within a decided time since the KIP9000 has started transporting the Roll 2 from the wait position. 2. Roll Set Sensor 2 Signal (RP_SET2) does not change from L to H within a decided time since the KIP9000 has started retrieving the Roll 2 back to wait position.
Remedy: Roll Set Sensor 2 (PH2) 1 Check the input signal from the Roll Set Sensor 2 (signal code 05) in the Input/Output Checking Mode of Service Mode. Is it “L” when the media is on the sensor and “H” when the media is not on the sensor? No 1. Check if the sensor harness has any abnormality. 2. Replace the sensor (PH2) if the harness is OK. Roll Paper Feed Clutch 2 (MC2) 2 Can the Roll Paper Feed Clutch 2 (signal code : 93) be operated properly in the Function Checking Mode of Service Mode? No 1. Check if the harness of clutch has any abnormality. 2. Replace the clutch (MC2) if the harness is OK. DC Driver PCB (PW7755) 3 Can the error be fixed by replacing the DC Driver PCB? Yes OK Main Control PCB (PW11520) 4 Can the error be fixed by replacing the Main Control PCB? Yes OK
Code: J-03
Description: Roll 3 Jam
Causes: 1. Roll Set Sensor 3 Signal (RP_SET3) does not change from H to L within a decided time since the KIP9000 has started transporting the Roll 3 from the wait position. 2. Roll Set Sensor 3 Signal (RP_SET3) does not change from L to H within a decided time since the KIP9000 has started retrieving the Roll 3 back to wait position.
Remedy: Roll Set Sensor 3 (PH3) 1 Check the input signal from the Roll Set Sensor 3 (signal code 06) in the Input/Output Checking Mode of Service Mode. Is it “L” when the media is on the sensor and “H” when the media is not on the sensor? No 1. Check if the sensor harness has any abnormality. 2. Replace the sensor (PH3) if the harness is OK. Roll Paper Feed Clutch 3 (MC3) 2 Can the Roll Paper Feed Clutch 3 (signal code : 94) be operated properly in the Function Checking Mode of Service Mode? No 1. Check if the harness of clutch has any abnormality. 2. Replace the clutch (MC3) if the harness is OK. DC Driver PCB (PW7755) 3 Can the error be fixed by replacing the DC Driver PCB? Yes OK Main Control PCB (PW11520) 4 Can the error be fixed by replacing the Main Control PCB? Yes OK
Code: J-04
Description: Roll 4 Jam
Causes: 1. Roll Set Sensor 4 Signal (RP_SET4) does not change from H to L within a decided time since the KIP9000 has started transporting the Roll 4 from the wait position. 2. Roll Set Sensor 4 Signal (RP_SET4) does not change from L to H within a decided time since the KIP9000 has started retrieving the Roll 4 back to wait position.
Remedy: Roll Set Sensor 4 (PH4) 1 Check the input signal from the Roll Set Sensor 4 (signal code 07) in the Input/Output Checking Mode of Service Mode. Is it “L” when the media is on the sensor and “H” when the media is not on the sensor? No 1. Check if the sensor harness has any abnormality. 2. Replace the sensor (PH4) if the harness is OK. Roll Paper Feed Clutch 4 (MC4) 2 Can the Roll Paper Feed Clutch 4 (signal code : 95) be operated properly in the Function Checking Mode of Service Mode? No 1. Check if the harness of clutch has any abnormality. 2. Replace the clutch (MC4) if the harness is OK. DC Driver PCB (PW7755) 3 Can the error be fixed by replacing the DC Driver PCB? Yes OK Main Control PCB (PW11520) 4 Can the error be fixed by replacing the Main Control PCB? Yes OK