PrintCopy.info service

HP Color LaserJet Pro MFP M477

Error Codes List page 1

  • Code: 30.0013
  • Display: 30.XXXX Scanner Error
  • Description: The flatbed or ADF scanner is failing to initialize
  • Causes: Scanner failed to find home
  • Remedy: 1. Verify that the product has the most recent firmware from hp.com. 2. Verify that the (flat flexible cables (FFC’s) are seated correctly on the formatter board. 3. If the error persists, replace the Scanner/ADF Assembly (HP Part #: CF377– 60104). 4. If the error persists, escalate to Level 3 so that Technical Marketing has visibility to the problem.
  • Code: 30.0016
  • Display: 30.XXXX Scanner Error
  • Description: The flatbed or ADF scanner is failing to initialize
  • Causes: Scan sensor communication error
  • Remedy: 1. Verify that the product has the most recent firmware from hp.com. 2. Verify that the (flat flexible cables (FFC’s) are seated correctly on the formatter board. 3. If the error persists, replace the Scanner/ADF Assembly (HP Part #: CF377– 60104). 4. If the error persists, escalate to Level 3 so that Technical Marketing has visibility to the problem.
  • Code: 30.0017
  • Display: 30.XXXX Scanner Error
  • Description: The flatbed or ADF scanner is failing to initialize
  • Causes: Scan motor exceeded max position error
  • Remedy: 1. Verify that the product has the most recent firmware from hp.com. 2. Verify that the (flat flexible cables (FFC’s) are seated correctly on the formatter board. 3. If the error persists, replace the Scanner/ADF Assembly (HP Part #: CF377– 60104). 4. If the error persists, escalate to Level 3 so that Technical Marketing has visibility to the problem.
  • Code: 30.0023
  • Display: 30.XXXX Scanner Error
  • Description: The flatbed or ADF scanner is failing to initialize
  • Causes: ADF scanner calibration error
  • Remedy: 1. Verify that the product has the most recent firmware from hp.com. 2. Verify that the (flat flexible cables (FFC’s) are seated correctly on the formatter board. 3. If the error persists, replace the Scanner/ADF Assembly (HP Part #: CF377– 60104). 4. If the error persists, escalate to Level 3 so that Technical Marketing has visibility to the problem.
  • Code: 49.XX.YY
  • Display: 49.XX.YY Error Messages
  • Description: The product has experienced an internal embedded software error. Under most conditions, the product automatically restarts.
  • Causes:
  • Remedy:

    1. Reset the printer: a. Turn off the power by using the power switch, and then wait at least 30 seconds. b. Turn on the power and wait for the product to initialize. 2. If you are using a surge protector: a. Power off the printer. b. Remove the surge protector. c. Plug the product directly into the wall socket and turn the product power on. 3. If the error persists, disconnect any network or USB cables and power cycle. If the product returns to Ready, check the FW version and update if a newer version is available. 4. If the error persists, print a Service Page from the Reports menu. Also, print an Error Report from the 2ndary Service Menu. On the Service Page, look at the xxxx portion of the 49.xxxx errors listed: • If the numbers are all or mostly different, then power quality is a possible problem; try a different wall socket. • If the xxxx portion of 49.xxxx contain repeats of the same numbers or groups of numbers, then check the 2ndary Service Error Report printed earlier for indications of a failure in a particular area. The report may indicate whether the error is caused by a network problem or a problem with the job. 5. If the error persists, replace the product. NOTE: If the 49 Error is caused by the network or a specific file, do not replace the product; it will not resolve the issue. Instead, attempt to isolate the issue in a way that demonstrates the error is caused by something in the environment. 6. If the error persists after product replacement, escalate to Level 3 so that Technical Marketing has visibility to the problem.

  • Code: 50.00
  • Display: 50.XX Fuser Error, Turn off then on
  • Description: The product has experienced an internal fuser hardware error
  • Causes: Generic Fuser error
  • Remedy: 1. Reset the product:a. Turn off the power by using the power switch, and then wait at least 30 seconds.b. Turn on the power and wait for the product to initialize.2. If you are using a surge protector:a. Power off the product.b. Remove the surge protector.c. Plug the product directly into the wall socket and turn the product power on.3. If the error persists, replace the Fusing Assembly: Fusing Assembly, 110 VAC, simplex models (HP Part #: RM2–6431–000CN Fusing Assembly, 220 VAC, simplex models (HP Part #: RM2–6436–000CN Fusing Assembly, 110 VAC, duplex models (HP Part #: RM2–6418–000CN Fusing Assembly, 220 VAC, duplex models (HP Part #: RM2–6435–000CN4. If the error persists, replace the product.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us