Display: Paper out or paper jam in the main tray, or the paper size is incorrect. Check the paper size settings or clear the jam and press the [Start] button.
Description: Paper out error
Causes: Failure to load paper to print.
Remedy: 1. Is the surface of LD Roller contaminated with micro pearl paper dust or greasy dirt? 1. Clean the LD Roller. 1. Is the surface of intermediate roller contaminated with micro pearl paper dust or greasy dirt? 1. Clean the intermediate roller. 1. Is the surface of Pick-up Rollers contaminated with micro pearl paper dust or greasy dirt? 1. Clean the Pick-up Roller. 1. Is the clutch of the Frame Assy L damaged? 1. Replace the printer mechanism with a new one. 1. Is the clutch of the Frame Assy R damaged? 1. Replace the printer mechanism with a new one.
Code: 08
Display: You need to replace the following ink cartridge(s).
Description: Ink end error
Causes: Ink is out in some I/C.
Remedy: 1. Is the Memory chip on the Ink Cartridge disconnected or damaged? 1. Replace the Ink Cartridge with a new one. 1. Is the CSIC FFC properly connected to CN5 connector on the Main Board and the connector on the CSIC Assy? 1. Connect the CSIC FFC correctly. 1. Is the CSIC terminal damaged? 1. Replace the CSIC Assy with a new one. 2. Is the CR contact module damaged? 2. Replace the CSIC Assy with a new one.
Code: 09
Display: Install the following ink cartridge(s).
Description: No ink cartridge error
Causes: I/C was not set.
Remedy: 1. Is the Memory chip on the Ink Cartridge disconnected or damaged? 1. Replace the Ink Cartridge with a new one. 1. Is the CSIC FFC properly connected to CN5 connector on the Main Board and the connector on the CSIC Assy? 1. Connect the CSIC FFC correctly. 1. Is the CSIC terminal damaged? 1. Replace the CSIC Assy with a new one. 2. Is the CR contact module damaged? 2. Replace the CSIC Assy with a new one.
Code: 10
Display: Cannot recognize the following ink cartridge(s). Install them correctly.
Description: Incorrect ink cartridge
Causes: Incorrect I/C was set.
Remedy: 1. Is the Memory chip on the Ink Cartridge disconnected or damaged? 1. Replace the Ink Cartridge with a new one. 1. Is the CSIC FFC properly connected to CN5 connector on the Main Board and the connector on the CSIC Assy? 1. Connect the CSIC FFC correctly. 1. Is the CSIC terminal damaged? 1. Replace the CSIC Assy with a new one. 2. Is the CR contact module damaged? 2. Replace the CSIC Assy with a new one.
Code: 11
Display: Replace the following ink cartridge(s) before cleaning the print head.
Description: Head cleaning (Ink low error)
Causes: Head cleaning was attempted in the Ink low status.
Remedy: 1. Is the Memory chip on the Ink Cartridge disconnected or damaged? 1. Replace the Ink Cartridge with a new one. 1. Is the CSIC FFC properly connected to CN5 connector on the Main Board and the connector on the CSIC Assy? 1. Connect the CSIC FFC correctly. 1. Is the CSIC terminal damaged? 1. Replace the CSIC Assy with a new one. 2. Is the CR contact module damaged? 2. Replace the CSIC Assy with a new one.
Code: 12
Display: The scanner unit is open. When replacing ink cartridge(s), close the scanner unit after replacing the cartridge(s).
Description: Scanner open error
Causes: Scanner Unit was opened during printing.
Remedy: 1. Is the Scanner Cover Open Sensor FFC properly connected to CN10 connector on the Main Board? 1. Replace the Scanner Unit with a new one. 2. Is the Scanner Cover Open Sensor FFC damaged? 2. Replace the Scanner Unit with a new one. 1. Is the Scanner Cover Open Sensor damaged? 1. Replace the Scanner Unit with a new one. 1. Is the Sensor magnet of the Carriage Unit damaged? 1. Replace the Carriage Unit with a new one. 1. Is the Open Sensor magnet of the Upper Housing damaged? 1. Replace the Upper Housing with a new one.