Xerox WorkCentre 7655
Service Mode 03. DC Quick (Table dC Routines)
Once in the Service Mode, diagnostic routines can be selected from the DC Quick menu.
Procedure
- Enter the PWS Diagnostic mode.
- Using the DC Quick pull-down menu (upper-right side of Diagnostics Service Entry Screen), select the desired dC routine. Table 1 is a complete list of dC routines that are available from the DC Quick pull-down menu.
Table 1 dC Routines
dC code | Name | Description |
---|---|---|
100 | Service Entry Screen | 1. Displays the Service Routine Tabs. 2. Lists Active Faults 3. Lists the item names of the HFSIs that exceeded life expectancy. 4. Lists the jams that have occurred since the last Call Closeout. 5. Displays IOT S/W Version. 6. Lists the total copies/prints |
102 | Software Upgrade | Allows the machine software to change |
104 | System Usage Counters | History of system usage |
105 | System Configuration | Install Phase (system), Install Phase (Main Controller), Product Identifier, Product Type, System Configuration, Line Frequency, Line Voltage, Customer Service Number, and Power Saver (current mode), Market Region Platform Options, NVRam Size and System Settings “Apply” Button. |
108 | Software Versions | System Software identifiers |
109 | Billing Counts | Billing Counter Data |
111 | ESS Logging | ESS Log type, current status, results, Faults that may have occurred, Debug Logging Enable/Disable buttons and “GetLog File Button. |
114 | ESS/Network Error Log | Occurrences of ESS shutdowns, errors, and warnings. |
115 | Maintenance Diagnostic Data | Machine usage data |
120 | Fault Counters | Number of Fault events from the last Complete Closeout (performed in Service Exit) to the current copy count. |
122 | Shut-down History | Most recent 40 Faults |
124 | ESS Fault Counts | Occurrences of ESS Faults |
129 | Automatic Setting: Adjust System Registration | The IOT lead registration and side registration are matched. |
131 | NVM access: Read/Write NVM | Reference or set/change the NVM data. |
132 | Set Machine Serial Number. Read Billing Meter Information | Sets the Machine Serial Number with assistance of service support. Reads Billing Meter Information for MCU PWB. |
133 | Time | Adjust System Time, System Date, Time Display Format, and GMI Offset. |
135 | Service Data HFSI Counter | Part replacement life expectancy (threshold) and current value (usage). Allows changing the replacement life expectancy to a preset value in the PWS database and reset the current value. |
140 | Analog Monitor | |
188 | Service Mode Exit Screen | Requirements for exit from the Service Mode. |
301 | NVM initialization | Initiates NVM Data initialization |
303 | CCM POST Self Test Routine | Provides access to a group of diagnostic tests that also run at system boot and application loading. |
312 | ESS Echo tests | Network echo tests by Protocol |
314 | Connectivity Tests | Connectivity Tests by Protocol |
327 | Admin Test | Resets Admin Pin |
330 | Component Check: Component Control | Instructions and results of the Input Component Check and Output Component Check 1. You can monitor each Input Component or check the operation of each Output Component. 2. You can simultaneously check multiple Input Components and Output Components up to 11 total. |
355 | Image Disk Diagnostics | Tests Image Disk, Displays Manufacturer, Model Number, Serial Number, Firmware Revision Level, Disk Size and Pass / Fail |
361 | Save Restore | Save and restore NVM values. |
362 | Compare | Compares NVM values with stored NVM values. |
372 | IOT Configuration | Number of paper trays and finishing devices installed. |
373 | Configuration Sheet | Enables and Disables Configuration Sheet Printing on Power Up. |
374 | Software Options | Displays the status of software options |
375 | ESS Network Configuration Backup and Restore | Backup and Restore network connectivity settings. |
402 | Software Verify | |
527 | Size Detection | Test size detection capabilities. |
606 | ESS Test Patterns | Enables ESS test printing according to composition and media size. |
612 | Color Test Pattern Print | Generates test pattern from different pattern generators in the machine (IOT, IIT, CCM PWB, Network Controller PWB). Patterns for use in identifying IQ problems, setting registration, and performing adjustments |
640 | Video Path Test | EPC Memory walking, Video Path integrity, and ESS <-> CCM communication. |
671 | Regi-Con Cycles | Measurement cycle check |
673 | Regi-Con Cycles | Control Sensor check |
675 | Regicon | Color Registration/Skew setup |
710 | No Paper Run | Tests paper feed and transportation subsystem without feeding paper. |
726 | Paper Timing Tests | Enables testing of times between |
740 | MSI Side Guide Adjustment | Sets the Side Guide for Min. and Max |
919 | Color Balance | |
924 | TRC Adjustment | Manually fine adjust each color (low/mid/high density) in PG. |
931 | In/Out | Adjusts the Inboard to Outboard Density (smile correction) |
937 | ProCon On/Off | Enables Printing and measures Process Control functions with the Process Controls either on or off for comparison. |
945 | IIT calibration | 1. Calculate and set the white reference compensation coefficient. 2. Correct the IIT sensitivity variation. |
950 | ATC Calibration | Enter ATC Sensor Calibration code into NVM. |
956 | Belt Edge Learn | Belt Edge Sensor Set up |
991 | Tone Up / Tone Down | Increases or decreases the toner concentration |