| Function |
Description |
| ESS Diag |
All Test |
Performs all ESS Diag tests except for MAC+PHY/USB Host/RTC. |
| FlashROM Test |
Calculates the checksum per Flash ROM header area and compares the result with the each area's prepared checksum stored in the ROM. |
| EEPROM Test |
Writes/reads/verifies the test pattern in the EEPROM area to be evaluated. |
| DRAM Test |
Writes the test data in the DRAM area to be evaluated. (Values will be overwritten with the original value after the test) |
| MAC+PHY Test |
Performs the loopback test for MAC (Media Access Control) and PHY (Physical Layer). |
| ASIC Test |
Performs the Regi check test. |
| Engine Test |
Performs the communication test between IOT. |
| Hard Drive Test (when the optional HD is installed) |
Performs the Hard Disk test. |
| USB Host Test (only when the optional USB is installed) |
Checks the communication between a USB Host port and the USB devices connected to the USB Host port. |
| RTC Test |
Performs the RTC test. |
| Engine Diag |
Sensor Test |
Checks the IOT switch and sensor operation. |
| Monitor Test |
Checks the clutch, solenoid, and motor drive operation. |
| Edit NVM |
Writes the NVM values. |
| Save NVM to ESS |
Saves the IOT NVM information in the ESS NVM. |
| Load NVM from ESS |
Loads all the NVM information in the ESS NVM into the IOT. |
| Initialize Slave |
|
| ROS Exposure |
Corrects the variation in the read-Regi of the Laser Unit. |
| Dew Prevention |
Specifies whether to set the Dew Prevention mode to ON or OFF. |
| Initial IU |
|
| Print Info |
Info Page |
Prints the printer configuration information on A4 paper. |
| Print Settings |
Prints the printer setting information on A4 paper. |
| Installation |
Serial No. |
Displays/specifies the serial number. |
| PagePack |
Displays the current PagePack status (Enable or Disable). |
| HexDump |
Specifies whether to set HexDump to ON or OFF. |
| Tone Correction (IOT tone correction) |
Specifies whether to set IOT Tone Correction to ON or OFF. |
| Pixel Counter |
Displays the last print pixel coverage (%) for 4 mm square meter in A4 paper, per Y/M/C/K color. |
| Configuration |
Operates the DIP switches on the NVM in ESS. |
| XCPT Mode |
Displays/Specifies the XCPT Mode setting. |
| Print Service |
Displays the current count of the Print Service. |
| Copy Service |
Displays the current count of the Copy Service. |
| FAX Service |
Displays the current count of the FAX Service. |
| Scan Service |
Displays the current count of the Scan Service. |
| Copy Counter M to B |
Copies the Master NVM values to the Backup NVM. |
| Copy Counter B to M |
Copies the Backup NVM values to the Master NVM. |
| Clear All NVM |
Initializes NVM. |
| Clear JobHistory |
Initializes the job data (log). |
| Clear AuditronPV |
Clears the AuditronPV data such as billing counter, user account and user restriction settings. |
| Hard Drive Erase (when the optional HD is installed) |
Deletes all data from the Hard Disk. |
| Clear DeviceData |
Deletes all data in the devices (EEPROM, SRAM, Fax Memory, Hard Disk). |
| Test Print |
No Image IOT |
Prints the IOT built-in test pattern. |
| Pattern IOT |
Prints the IOT built-in test pattern. |
| Grid 2 ESS |
Prints the ESS built-in grid pattern. |
| Cyan 20% ESS |
Fills one side of paper in the density of 20 % of cyan. |
| Magenta 20% ESS |
Fills one side of paper in the density of 20 % of magenta. |
| Yellow 20% ESS |
Fills one side of paper in the density of 20 % of yellow. |
| Black 20% ESS |
Fills one side of paper in the density of 20 % of black. |
| CMY 20% ESS |
Fills one side of paper in the density of 20 % of the mixture of cyan, magenta, and yellow. |
| Gradation ESS |
Prints the ESS built-in gradation pattern. |
| Toner Pallet Check |
Prints four bars, filled with 100% density of each color (C/M/Y/K), lined on the paper. * Use this for checking the density of each toner cartridge. |
| Contamination Chk |
Prints 5 sheets of paper with the pattern of millimeter scale on the top/left edges and inch scale on the bottom/right edges, each filed with Y/M/C/K color of 20% density, and the one that identifies defects. |
| Parameter |
Regi |
Displays/specifies the Regi current set value. |
| Life |
Displays the current counter of the consumables life. |
| Print |
Prints the parameter of the IOT and the error count. |
| Exit Mode |
Exit Mode |
Exits Service Mode and restarts the printer. |
| Board Diag |
All Test |
Continually performs the Fax Memory, Fax Card I/F, AFE Serial I/F, IIT I/F, and ASIC tests. |
| Fax Flash W/R Test |
Performs write/read tests of the Fax Flash Memory. |
| SRAM W/R Test |
Performs write/read tests of the Fax SRAM. |
| I/F Test |
Performs the communication test between Fax Card, AFE, and IIT. |
| ASIC Test |
Performs the ASIC built-in IJAC/JBIG test. |
| Relay Test |
Toggles the Relay signal at the specified frequency. |
| Hook Test |
Toggles the Hook signal at the specified frequency. |
| Single Tone Test |
Continuously sends the tone at the selected frequency. |
| DTMF Send |
Continuously sends the DTMF signal. |
| Dial Pulse Send |
Sends the multi-digits Dial Pulse (10/20pps) signal. |
| Ring Back Tone |
Sends the ringback tone. |
| Data Send |
Specifies the speed and pattern for checking data forwarding (no pattern for V.34) |
| Line Voltage |
Checks the status of the Line Voltage. |
| Line Current |
Checks the status of the Line Current. |
| Information |
Scan Counter |
Displays the Scan counter value. |
| Scanner Maintenance |
White Balance |
Adjusts the white balance automatically. |
| Shading Parameter |
Specifies the Shading factor setting. |
| Registration Param. |
Adjusts the Registration. |
| Auto Registration |
Specifies whether the Auto Reg adjust function to set to ON or OFF. |
| Sensor Parameter |
Specifies the power control value of the Feed Sensor. |
| Vertical Scan Mag. |
Specifies the parameter setting of the magnification for the vertical scanning. |
| Test Pattern |
Specifies the test pattern and the parameter setting. |
| IIT I/O Check |
Checks the input and output of the scanner components. |
| Scan Counter Clear |
Clear the scan counter. |
| Carriage Drive_100 |
|
| Backup Data |
All Clear |
Deletes the SRAM/EEPROM backup data. |
| User Clear |
Deletes the SRAM/EEPROM backup data. |
| System Clear |
Deletes the SRAM/EEPROM backup data. |
| User&System Clear |
Deletes the SRAM/EEPROM backup data. |
| System Data Init |
Deletes the SRAM/EEPROM backup data. |
| Document Clear |
Deletes the SRAM/EEPROM backup data. |
| Complete |
Complete |
Exits Service Mode and restarts the printer. |