Toshiba e-Studio 2523AD
Service Mode. Overview
Overview
Starting each mode
To enter into the desired mode, turn the power ON while pressing the two digital keys designated to each mode (e.g. [0] and [5]) simultaneously, and then hold those keys until the LED of the [ENERGY SAVER] button is lit.
On the authentication screen displayed after starting up each mode, enter the service password, and then press [OK]. The password is not set by default.
Exiting from each mode
Turn off the main switch to exit the self diagnosis mode.
List of modes
Mode | For start | Contents | For exit | Display | Model | |
---|---|---|---|---|---|---|
2523A/ 2523AD/ 2323AM/ 2823AM |
2329A/ 2829A |
|||||
Control panel check mode | [0] + [1] + [POWER] | All LEDs on the control panel are lit, and all the LCD pixels blink. | [POWER] OFF/ON | All the LCD pixels blink. | Y | Y |
Test mode | [0] + [3] + [POWER] | Checks the status of input/output signals. | [POWER] OFF/ON | TEST_MODE_C MC= | Y | Y |
Test print mode | [0] + [4] + [POWER] | Outputs the test patterns. | [POWER] OFF/ON | TEST_MODE_P ENTER THE CODE DRAWER PAPER TYPE |
Y | Y |
Adjustment mode | [0] + [5] + [POWER] | Adjusts various items. | [POWER] OFF/ON | TEST_MODE_A MC= | Y | Y |
Setting mode | [0] + [8] + [POWER] | Sets various items. | [POWER] OFF/ON | TEST_MODE_D MC= | Y | Y |
Assist mode | [3] + [CLEAR] + [POWER] | When replacing the MAIN circuit board, the assistance mode can be used to configure memory clear and memory safe delete. | [POWER] OFF/ON | FIWMWARE ASSIST MODE CLEAR SRAM ERASE SRAM SECURELY |
Y | Y |
List print mode | [9] + [START] + [POWER] | Prints various lists. | [POWER] OFF/ON | TEST_MODE_L ENTER THE CODE DRAWER | Y | Y |
PM support mode | [6] + [START] + [POWER] | Clears each counter. | [POWER] OFF/ON | PM SUPPORT MODE ENTER THE CODE | Y | Y |
Flash memory clear mode | [6] + [CLEAR] + [POWER] | Mode for clearing the Flash memory and setting the MFP Serial No. | [POWER] OFF/ON | SRAM CLEAR MODE SET SERIAL NUMBER CLEAR SRAM ENGINE SPEED INIT. |
Y | Y |
Flash memory backup/ restore mode | [5] + [9] + [POWER] | Backup and restore the flash memory data to USB device. | [POWER] OFF/ON | SRAM COPY MODE BACKUP SRAM DATA RESTORE SRAM DATA |
Y | Y |
Firmware update mode | [4] + [9] +[POWER] |
Performs firmware update with USB device. | [POWER] OFF/ON | FW Update Mode SYSTEM FW ENGINE FW ALL |
Y | Y |
Password reset mode | [4] + [8] + [9] + [POWER] | Resets the administrator password and service password. | [POWER] OFF/ON | PASSWORD RESET MODE RESET PASSWORD=OK |
Y | Y |
FAX clear mode | [1]+[*] +[POWER] |
Initialization of the various memory areas (user registration area, system setting area, image data area) | [POWER] OFF/ON | TEST_MODE CL MC= | - | Y |
Job clear mode | [1]+[7] +[POWER] |
Clear all the jobs stored in this equipment. | [POWER] OFF/ON | No special display. After clearing, normal screen will be displayed. | - | Y |
BIOS mode |
[OK] + [POWER] | Starts the equipment with the BIOS mode. | [POWER] OFF/ON | *BIOS MODE* 20XX/XX/XX V0.XX | Y | Y |
EPU mode | [FC] + [START] + [POWER] |
Performs a series of operations from the auto toner initial adjustment, supplying of the developer material to the automatic gamma adjustment. | [POWER] OFF/ON | EPU MODE OPEN FRONT COVER REMOVE DEV. CARTRIDGE |
Y | Y |