Sharp MXM753U
Simulation mode. List of simulation codes 49 - 67
| Main | Sub | Functions | Section |
|---|---|---|---|
| 49 | 1 | Used to perform the firmware update. | |
| 3 | Used to install and update the Operation Manual data stored in the HDD. | ||
| 5 | Used to install and update the watermark data stored in the HDD. | ||
| 50 | 1 | Copy image position, image loss adjustment | |
| 2 | Used to adjust the copy image position and the image loss (simple adjustment). | ||
| 5 | Used to adjust the print lead edge image position. (PRINTER MODE) | ||
| 6 | Used to adjust the copy image position and the image loss (DSPF mode). | Automatic document feeder | |
| 7 | Used to adjust the copy image position and the image loss (DSPF mode) (simple adjustment). | Automatic document feeder | |
| 10 | Used to adjust the image off-center position. (The adjustment is made separately for each paper feed section.) |
||
| 12 | Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) | ||
| 27 | Used to perform the image loss adjustment of scanned images in the FAX or image send mode. | ||
| 28 | Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio. | ||
| 51 | 2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the DSPF resist roller. | |
| 53 | 6 | Used to adjust the detection level of the DSPF document width. | |
| 7 | Used to adjust the DSPF document size width sensor. | Automatic document feeder | |
| 8 | Used to adjust the document lead edge reference and the DSPF mode document scan position. | Automatic document feeder | |
| 55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
| 2 | Used to set the specifications of the scanner control operation. (SOFT SW) | ||
| 3 | Used to set the specifications of the controller operation. (SOFT SW) | ||
| 10 | Used to set the stamp text. | ||
| 56 | 1 | Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) | |
| 2 | Used to backup the data in the EEPROM. SRAM, and HDD (including user authentication data and address data) to the USB memory. | ||
| 3 | Used to backup the document filing data to the USB memory. | ||
| 4 | Used to backup the JOB log data to the USB memory. | ||
| 60 | 1 | Used to check the operations (read/write) of the MFP PWB memory. | |
| 2 | Used to set the specifications of the MFP PWB on-board SDRAM. | ||
| 61 | 1 | Used to check the LSU polygon motor rotation and laser detection. | LSU |
| 3 | Used to set the laser power | ||
| 62 | 1 | Used to execute the hard disk format (except operation manual area). * If no HDD is installed, the MFP Flash memory is formatted. |
|
| 2 | Used to check read/write of the hard disk (partial). | ||
| 3 | Used to check read/write of the hard disk (all areas). | ||
| 6 | Used to perform the self diagnostics of the hard disk. | ||
| 7 | Used to print the hard disk self diagnostics error log. | ||
| 8 | Used to format the hard disk. (Excluding the system area and the operation manual area) | ||
| 10 | Used to delete the job log data. | ||
| 11 | Used to delete the document filing data. | ||
| 12 | Used to set Enable/Disable of auto format in a hard disk trouble. | ||
| 13 | Used to format the hard disk. (only the operation manual and watermark area) | ||
| 63 | 1 | Used to display the shading correction result. | Scanner |
| 2 | Used to perform shading. | ||
| 3 | Used to perform scanner (CCD/CIS) color balance and gamma auto adjustment. | Scanner | |
| 4 | Used to display the SIT chart patch density. | ||
| 5 | Used to perform the scanner (CCD/CIS) color balance and gamma default setting. | ||
| 64 | 2 | Test print. (Self print) (Monochrome mode) | |
| 4 | Printer test print. (Self print) (256 gradation) * This simulation functions only for the machines which are provided with the printer function. |
||
| 5 | Printer test print. (Self print) (PCL) | ||
| 6 | Printer test print. (Self print) (PS) | ||
| 7 | Test print. (Self print) (Used to print the adjustment pattern of SIM46-16.) | ||
| 65 | 1 | Used to adjust the touch panel (LCD display section) detection coordinates. | Operation panel section |
| 2 | Used to display the touch panel (LCD display section) detection coordinates. | ||
| 5 | Used to check the operation panel key input. | ||
| 67 | 17 | Printer controller reset | Printer |
| 24 | Used to adjust the printer density. (Automatic adjustment) | Printer | |
| 25 | Printer density adjustment (manual adjustment) (this simulation functions only for the machines which are provided with the printer function). | Printer | |
| 31 | Used to clear the printer calibration data (this simulation functions only for the machines which are provided with the printer function). | Printer | |
| 33 | Used to adjust the gamma and the density in each printer screen (this simulation functions only for the machines which are provided with the printer function). | Printer | |
| 34 | Used to set the density correction in the printer high density section. (Support for the high density section tone gap) | Printer | |
| 70 | MFP PWB SRAM data clear | MFP PWB |