Sharp MXM350N

Communication specification when a trouble occurs

The image send/receive specifications when a trouble occurs are as shown below.

✕ Check (Clean, replace, or adjust as necessary.) ❍ Clean ▲ Replace Δ Adjust ✩ Lubricate ❏ Move position

Trouble	Send reservation	Print	FAX call request	FAX call-in	LAN send	LAN receive	Precaution
PCU breakdowns (Excluding C1, C2, C3, H2, H3, H4, H5, L4, L8, U2- 90, U2-91, and skating check error)	❍	×	❍	Note	❍	Note	There is a risk that the memory is full.
Scanner breakdowns (L1, L3, U2- 80, U2-81)	×	❍	❍	❍	❍	❍
F6, F7 (FAX breakdown)	×	❍	×	×	❍	❍
F1 (Paper exit section breakdown)	❍	Δ4	❍	❍	❍	❍
F3, U6 (Paper feed tray breakdown)	❍	Δ2	❍	❍	❍	❍
E7 (01, 06) (ICU breakdown)	×	×	×	×	❍	❍
E7-02 (Laser breakdown)	❍	×	❍	Note	×	Note	There is a risk that the memory is full.
E7-03 (HD breakdown)	×	×	×	×	×	×
E7 (10, 11, 14) (CCD breakdown)	×	❍	❍	❍	❍	❍
E6 (10, 11, 14) (CIS breakdown)	Δ6	❍	❍	❍	❍	❍
E7-80 (Scanner communication trouble)	×	❍	❍	❍	❍	❍
E7-90 (PCU communication trouble)	×	×	×	×	×	×
E7 (50, 60) (Skating check error)	×	×	×	×	×	×
U2 (00, 11, 12, 22) (ICU memory error)	×	×	×	×	×	×
U2 (22, 23) (SRAM check sum error)	×	×	×	×	×	×
U2-50 (HD check sum error)	×	×	×	×	×	×
U7 (RIC external communication disable), PF	×	×	×	×	×	×	Inhibition of use by a customer having outstanding fee
U1 (Backup battery voltage fall)	×	Δ3	× Note	×	× Note	×	Transfer enable
L4-30 (Controller fan motor trouble)	×	×	×	×	×	×
Door open	❍	×	❍	❍ Note	❍	Note	There is a risk that the memory is full.
Toner empty	❍	×	❍	❍ Note	❍	Note	There is a risk that the memory is full.
Process cartridge uninstalled, etc.	❍	×	❍	❍ Note	❍	Note	There is a risk that the memory is full.
Paper empty	❍	×	❍	❍ Note	❍	Note	There is a risk that the memory is full.
Paper JAM	❍	×	❍	❍ Note	❍	Note	There is a risk that the memory is full.
Document JAM	×	❍	❍	❍	❍	❍
Simulation	×	×	×	×	×	×
Key operation (Communication disable)	×	×	×	×	×	×

Δ2: Enable except for the trouble tray
* When, however, a paper feed tray trouble is detected during a job, the engine is stopped and printing is disabled.
Δ3: The display goes to the FAX status check menu and the list can be printed.: The received document is outputted.
Δ4: Paper exit is enabled except for the trouble paper exit tray
* When, however, a paper feed tray trouble is detected during a job, the engine is stopped and printing is disabled.
Δ5: Only the operation related to image quality can be executed depending on the destination. (low density print)
Δ6: The operation can be executed in the single surface scanning mode.

Writing to the trouble memory

In case of a same trouble in this machine, selection is made with the simulation to write into the trouble memory or not. If this simulation is set, any trouble is written into the trouble memory unconditionally.

(SIMULATION. 26-35)
0: A same trouble as the previous one is not written. (Default)
1: Any trouble is written into the trouble memory unconditionally.