Sharp MXM315NE
Simulation mode. List of codes 43-55
Main | Sub | Functions | Section |
---|---|---|---|
43 | 1 | Used to set the fusing temperature in each mode. | |
4 | Used to set the fusing temperature 2 in each mode. | ||
10 | Used to set the postcard feed cycle | ||
20 | Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature setting of each paper (SIM43-01). | ||
22 | Used to perform the low-temperature, low-humidity (L/L) environment correction for the fusing temperature setting of each paper (SIM43-04). | ||
44 | 1 | Used to set each correction operation function in the image forming (process) section. | Image process (Photoconductor/ Developing/Transfer/Cleaning) |
9 | Used to display the result data of the high density process control operation. | Image process (Photoconductor/ Developing/Transfer/Cleaning) | |
14 | Used to display the output level of the temperature and humidity sensor. | Process (OPC drum, development)/Fusing/LSU | |
43 | Used to display the identification information of the developing unit. | Developing system | |
46 | 2 | Used to adjust the copy density in the copy mode. | |
4 | Used to adjust the density in the image send mode. (Color scanner) | ||
5 | Used to adjust the density in the image send mode. (Monochromatic scanner) | ||
8 | Used to adjust the image send mode color balance RGB. | ||
9 | Used to adjust the scan image density. | ||
19 | Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode documents. | ||
30 | Used to adjust the resolution in the sub scanning direction in the copy mode. | ||
32 | Used to adjust the document background density reproducibility in the monochrome auto copy mode. | ||
37 | Used to adjust the reproduction capability of monochrome mode color. | ||
39 | Used to adjust the sharpness of FAX send images. | ||
40 | Used to adjust the FAX send image density. (Collective adjustment of all the modes) | ||
41 | Used to adjust the FAX send image density. (Normal) | ||
42 | Used to adjust the FAX send image density. (Fine) | ||
43 | Used to adjust the FAX send image density. (Super Fine) | ||
44 | Used to adjust the FAX send image density. (Ultra fine) | ||
45 | Used to adjust the FAX send image density. (600dpi). | ||
47 | Used to set the compression rate of copy and scan images (JPEG). | ||
60 | Used to adjust the sharpness in the color auto copy mode. | ||
61 | Used to adjust the area separation recognition level. | ||
62 | Used to set the operating conditions of the ACS, the area separation, the background image process, and the auto exposure mode. | ||
63 | Used to adjust the density in the copy low density section. | ||
48 | 1 | Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direction). | |
5 | Used to correction the scan image magnification ratio (in the sub scanning direction). | Scanner section | |
49 | 1 | Used to perform the firmware update. | |
3 | Used to update the operation manual in the HDD. | ||
5 | Used to perform the watermark update. | ||
50 | 1 | Copy image position, image loss adjustment | |
5 | Used to adjust the print lead edge image position. (PRINTER MODE) | ||
6 | Used to adjust the copy image position and the image loss. (RSPF mode) | RSPF | |
10 | Used to adjust the black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) | ||
12 | Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) | ||
27 | Used to perform the image loss adjustment of scanned images in the FAX or image send mode. | ||
28 | Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio. | ||
51 | 1 | Used to adjust the ON/OFF timing of the transfer current. | |
2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF registration roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) | ||
9 | Used to adjust the ON/OFF timing of the separation voltage. | ||
53 | 6 | Used to adjust the detection level of the RSPF document width. | |
7 | Used to adjust the RSPF document size width sensor. | ||
8 | Used to adjust the document lead edge reference and the RSPF mode document scan position. | ||
9 | RSPF dirt detection setting. | ||
10 | RSPF dirt detection execution. | ||
55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
2 |
Used to set the specifications of the scanner control operation. (SOFT SW) |
|
|
3 |
Used to set the specifications of the controller operation. (SOFT SW) |
|
|
10 |
Used to set the special stamp text. (Taiwan only) |
|