Sharp MXM1100
Simulation mode. List of simulation codes 26 - 46
| Main | Sub | Function (Purpose) | Section | Purpose |
|---|---|---|---|---|
| 26 | 52 | Used to set whether non-print paper (insertion, cover sheet) is counted or not. | Setting | |
| 69 | Used to set preliminary preparation of toner and near end display when the toner quantity reaches 25%. | Setting | ||
| 27 | 1 | Used to set non-detection of the communication error (U7-00) with RIC. | Setting | |
| 2 | Used to set the FSS function (user registration number, Host server telephone number). | Setting | ||
| 4 | Used to set the FSS function (initializing, call, toner order auto send). | Setting | ||
| 5 | Used to set the machine tag No. (This simulation allows to check the machine tag No. from the host computer side.) |
Communication (RIC/MODEM) | Setting | |
| 6 | Used to set the FSS function (manual service call). | Setting | ||
| 7 | Used to set the FSS function (enable, Alert calling) | Setting | ||
| 9 | Used to set the paper transport time between sensors and the gain adjustment retry number. | Setting | ||
| 10 | Used to clear the trouble prognosis history information. | Data clear | ||
| 11 | Used to check the serial communication retry number history and the scanner GAIN adjustment retry number history. | Other | ||
| 12 | Used to check the error history of high density, half-tone potential, and dark potential. | Other | ||
| 13 | Used to check the history of paper transport time between sensors. | Other | ||
| 14 | Used to set the FSS function connection mode. (Enable only for Disable to Enable) | Setting | ||
| 30 | 1 | Used to check the operation of the sensors and the detectors in other than the paper feed section and the control circuits. | Operation test/check | |
| 2 | Used to check the operation of the sensors and the detectors in the paper feed section and the control circuits. | Operation test/check | ||
| 10 | Used to check the Main unit double feed detection sensor (Paper feed) | (Must not be used unless a special change is required.) | ||
| 33 | 1 | Used to check the operation of the sensors in the card reader and the control circuit. | Operation test/check | |
| 2 | The card ID (IDM) information supporting the Felica card in the machine user registration information is deleted. | Data clear | ||
| 40 | 2 | Used to adjust the detection level of the manual paper feed tray paper width detector. | Paper feed | Adjustment/ Setting |
| 7 | Used to adjust the manual paper feed tray size width detection level. | Paper feed | Adjustment/ Setting | |
| 12 | Used to adjust the tray 4 width detection level. | Paper feed | Adjustment/ Setting | |
| 41 | 1 | Used to check the operation of the document size sensor and the control circuit. | Operation test/check | |
| 2 | Used to adjust the document size sensor detection level. | Adjustment | ||
| 3 | Used to check the operation of the document size sensor and the control circuit. | Operation test/check | ||
| 43 | 1 | Used to set the fusing temperature of each paper mode. | Setting | |
| 31 | Used to check the operation of the fusing web cleaning motor and the control circuit. | Operation test/check | ||
| 32 | Used to set the forcible operation of the fusing web cleaning when job end. | Adjustment/ Setting | ||
| 33 | Used to make setting of before-fusing PG operations. | Setting | ||
| 44 | 1 | Used to set each correction function of the image forming (process) section. | Process (OPC drum, developing, transfer, cleaning) | Setting |
| 2 | Used to adjust the process control sensor gain. | Process | Adjustment/ Setting | |
| 3 | A change in the OPC drum surface potential VO due to the OPC drum environment and membrane decrease (life) is detected with the surface potential sensor to correct the grid potential Vg so that the cleaning field is maintained at a constant level. | Process | Operation test/check | |
| 4 | Used to set the operating conditions of the high density process control. | (Must not be used unless a special change is required.) | ||
| 5 | Used to set the dark potential adjustment conditions. | Adjustment/ Setting | ||
| 6 | Used to perform forcible execution of the high density process correction. | Adjustment | ||
| 7 | Used to clear the high density process control correction data. | Data clear | ||
| 9 | Used to display the process data. | Process (OPC drum, developing, transfer, cleaning) | (This simulation is normally not used in the market.) | |
| 12 | Used to display the result of the high density process control. | Process (OPC drum, development) | (This simulation is normally not used in the market.) | |
| 14 | Used to check the output levels of the fusing temperature sensor, the machine temperature sensor, and the humidity sensor. | Process (OPC drum, development) | Adjustment/ Setting/ Operation data check | |
| 16 | Used to check the toner density control data. | (This simulation is normally not used in the market.) | ||
| 28 | Used to set the process control execution timing. | Adjustment/ Setting | ||
| 33 | Used to set the conditions of the half-tone potential adjustment. | Adjustment/ Setting | ||
| 34 | Used to execute the half-tone potential adjustment compulsorily. | |||
| 35 | Used to display the half-tone potential adjustment result. | |||
| 36 | Used to clear the half-tone potential adjustment correction quantity. | Data clear | ||
| 46 | 2 | Used to adjust the copy density adjustment in the copy mode. | Adjustment (B/W copy mode) |
|
| 4 | Used to adjust the density in the scanner mode. | Adjustment (Color scanner mode) |
||
| 5 | Used to adjust the density in the scanner mode. | Adjustment (Monochrome scanner mode) |