| Main |
Sub |
Functions |
Section |
| 22 |
1 |
Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) |
|
| 2 |
Used to check the total numbers of mis-feed and troubles. (When the number of total jam is considerably great, it is judged as necessary for repair.) |
|
| 3 |
Used to check mis-feed positions and the mis-feed count of each position. * Presumption of the faulty point by this data is possible. |
|
| 4 |
Used to check the trouble (self diag) history. |
|
| 5 |
Used to check the ROM version of each unit (section). |
Firmware |
| 6 |
Used to output various adjustment/setting data (simulations, FAX soft switch counter), the firmware version, the counter list, the process control data, and SIM50-24 data. |
|
| 8 |
Used to check the number of operations (counter value) of the finisher, the RSPF, and the scan (reading) unit. |
|
| 9 |
Used to check the number of use (print quantity) of each paper feed section. |
Paper feed, ADU |
| 10 |
Used to check the system configuration (option, internal hardware). |
|
| 13 |
Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge). |
Process |
| 90 |
Used to output the various set data lists. |
|
| 23 |
2 |
Used to output the trouble history list of paper jam and mis-feed. (If the number of troubles of mis-feed is considerably great, the judgment is made that repair is required.) |
|
| 80 |
Used to check the operation of paper feed and paper transport in the paper feed section and the paper transport section. Used to output the list of the operation status of the sensor and the detectors in the paper feed section and the paper transport section. |
Paper feed, Paper transport |
| 24 |
1 |
Used to clear the jam counter, and the trouble counter. (After completion of maintenance, clear the counters.) |
|
| 2 |
Used to clear the number of use (the number of prints) of each paper feed section. |
|
| 3 |
Used to clear the finisher counter. |
|
| 4 |
Used to clear the maintenance counter, the printer counters of the transport unit and the fusing unit. (After completion of maintenance, clear the counters.) |
|
| 5 |
Used to clear the developer counter. (After replacement of developer, clear the counter.) |
|
| 7 |
Used to clear the OPC drum counter. (After replacement of the OPC drum, clear the counter.) |
|
| 9 |
Used clear the printer mode print counter and the self print mode print counter. |
|
| 30 |
Used to initialize the administrator password. |
|
| 31 |
Used to initialize the service mode password. |
|
| 34 |
Used to initialize the set items of SIM26-32. |
|
| 25 |
1 |
Used to check the operations of the developing section. |
Process (Developing section) |
| 2 |
Used to make the initial setting of toner density when replacing developer. (Automatic adjustment) |
Image process (Photo-conductor/ Developing/Transfer/Cleaning) |
| 26 |
2 |
Used to set the paper weight type. |
Paper feed |
| 6 |
Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination. |
|
| 18 |
Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.) |
|
| 30 |
Used to set the operation mode corresponding to the CE mark (Europe safety standards). (For slow start to drive the fusing heater lamp) |
|
| 32 |
Used to set display or non-display of the system setting menu. |
|
| 35 |
Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly. There are two display modes: display as one trouble and display as several series of troubles. |
|
| 38 |
Used to set Continue/Stop of print when the maintenance life is reached. |
|
| 50 |
Used to set functions. |
|
| 52 |
Used to set whether non-printed paper (insertion paper, cover paper) is counted up or not. |
|
| 55 |
Used to set Enable/Disable of the automatic color calibration (automatic color balance adjustment) when replacing a consumable part. (In this simulation, the menu is displayed but it does not work.) |
|
| 65 |
Used to set the staple process restriction. |
|
| 69 |
Used to set the operating conditions for toner near end. |
|
| 74 |
Used to set the OSA trial mode. |
|
| 78 |
Used to set the password of the remote operation panel. |
|
| 27 |
5 |
Used to set the machine tag No. (This function allows the host computer to check the machine tag No.) (FSS function) |
Communication (RIC/MODEM) |
| 9 |
Used to set the paper transport time recording YES/NO threshold value. (FSS function) |
|
| 10 |
Used to clear the trouble prediction history information. (FSS function) |
|
| 11 |
Used to check the serial communication retry number and the scanner gain adjustment retry number history. (FSS function) |
|
| 12 |
Used to check the high-density, halftone process control and the automatic registration adjustment error history. (FSS Function) |
|
| 13 |
Used to check the history of paper transport time between sensors. (FSS function) |
|
| 30 |
1 |
Used to check the operations of the sensors and the detectors in other than the paper feed section and the control circuits. |
|
| 2 |
Used to check the operations of the sensors and the detectors in the paper feed section and the control circuits. |
|
| 40 |
2 |
Manual paper feed tray paper width sensor adjustment. |
Paper feed |
| 7 |
Used to set the adjustment value of the manual paper feed tray paper width sensor. |
Paper feed |