Sharp MX7090
Simulation mode. List of Classic mode. Codes 26 - 44
Main | Sub | Functions | Section |
---|---|---|---|
26 | 3 | Used to set the specifications of the auditor. (Setting must be made according to the auditor use conditions.) |
Auditor |
5 | Used to set the count mode of the total counter and the maintenance counter. (A3/11x17 size) | ||
6 | Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination. | ||
7 | Used to set the machine ID. | ||
8 | Counter mode setting (Long scale) | ||
10 | Used to set the trial mode of the network scanner. | ||
18 | Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.) | ||
30 | Used to set the operation mode corresponding to the CE mark (Europe safety standards). (For slow start to drive the fusing heater lamp) | ||
32 | Used to set the specifications of the fusing cleaning operation. | Fusing | |
35 | Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly. There are two display modes: display as one trouble and display as several series of troubles. | ||
38 | Used to set Continue/Stop of print when the maintenance life is reached. | ||
41 | Used to set Enable/Disable of the magnification ratio automatic select function (AMS) in the center binding mode. | ||
49 | Used to set the print speed of postcards mode. | ||
50 | Used to set functions. | ||
52 | Used to set whether non-printed paper (insertion paper, cover paper) is counted up or not. | ||
60 | Used to setup the utility counter mode history data. | ||
61 | Used to setup the threshold for coverage. | ||
65 | Used to set the finisher alarm mode. | ||
66 | Simulation password setting. | ||
69 | Used to set the operating conditions for toner near end. | ||
73 | Enlargement continuous shoot, A3 wide copy mode image loss (shade delete quantity) adjustment | ||
74 | Used to set the OSA trial mode. | ||
78 | Used to set the password of the remote operation panel. | ||
79 | Used to set YES/NO of the pop-up display of user data delete result. | ||
85 | Simulation function setting. | ||
27 | 2 | Used to set the sender's registration number and the HOST server telephone number. (FSS function) | |
4 | Used to set the initial call and toner order auto send. (FSS function) | ||
5 | Used to set the machine tag No. (This function allows the host computer to check the machine tag No.) (FSS function) | Communication (RIC/MODEM) | |
6 | Used to set of the manual service call. (FSS function) | ||
7 | Used to set of the enable, alert callout. (FSS function) | ||
9 | Used to set the paper transport time recording YES/NO threshold value and shading gain adjustment retry number. (FSS function) | ||
10 | Used to clear the trouble prediction history information. (FSS function) | ||
11 | Used to check the serial communication retry number and the scanner gain adjustment retry number history. (FSS function) | ||
12 | Used to check the high density, halftone process control and the automatic registration adjustment error history. (FSS Function) | ||
13 | Used to check the history of paper transport time between sensors. (FSS function) | ||
14 | Used to set the FSS function connection test mode. | ||
15 | Used to display the FSS connection status. | ||
16 | Used to set the FSS alert send. | ||
17 | Used to set the FSS paper order alert. | ||
30 | 1 | Used to check the operations of the sensors and the detectors in other than the paper feed section and the control circuits. | |
2 | Used to check the operations of the sensors and the detectors in the paper feed section and the control circuits. | ||
10 | Used to check the operations of the Main unit double feed sensor. | ||
40 | 2 | Manual paper feed tray paper width sensor adjustment. | Paper feed |
7 | Used to set the adjustment value of the manual paper feed tray paper width sensor. | Paper feed | |
12 | Used to adjust the tray 4 width detection level. | Paper feed | |
41 | 1 | Used to check the operations of the document size sensor and the control circuit. | |
2 | Used to adjust the document size sensor detection level. | ||
3 | Used to check the operations of the document size sensor and the control circuit. | ||
43 | 1 | Used to set the fusing temperature in each mode. | |
2 | Used to set the fusing operation and preheating. | ||
20 | Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-1) in each paper mode. | ||
21 | Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-1) in each paper mode. | ||
24 | Used to set the correction of the temperature adjustment value of SIM 43-1. | ||
31 | Used to check fusing web cleaning. | ||
32 | Used to set various items related to the forcible operation of web cleaning when job end. | Fusing | |
35 | Fusing nip operation check | Fusing | |
44 | 1 | Used to set each correction operation function in the image forming (process) section. | Image process (Photoconductor/ Developing/Transfer/Cleaning) |
2 | Used to adjust the sensitivity of the image density sensor (registration sensor). | Process | |
4 | Used to set the conditions of the high density process control operation. | Process |