Riso SF5050
Test Mode. List of Test Modes 0140 - 0160
| Unit | No. | Name | Description | Setting | Model | ||
|---|---|---|---|---|---|---|---|
| SF9 | SF5*5 | SF5*3 | |||||
| Sys/ Panel |
0140 | Scan/Master-Making Independent Mode | Specifies whether the scanning action and the master removal action are executed in series or in parallel. | Setting value: 0: In parallel <default> 1: In series |
× | о | о |
| Sys/ Panel |
0141 | Counter Display Control | Specifies whether to display the counter display. | Setting value: 0: Not display 1: Display <default> |
o | о | о |
| Sys/ Panel |
0143 | Maintenance-Master Count Entry |
Sets the number of masters ( = MC) that triggers the maintenance-call message. | Setting range: 0 to 999900 masters (The entered value must be 0 to 9999.) Unit: 1 (The value of 1 means 100 masters.) Default: 0 (0 master: The maintenance call is not triggered.) |
о | о | о |
| Sys/ Panel |
0144 | Maintenance-Copy Count Entry | Sets the number of prints on the machine ( = TC) that triggers the maintenance- call message. | Setting range: 0 to 9999000 prints (The entered value must be 0 to 9999.) Unit: 1 (The value of 1 means 1000 prints.) Default: 0 (0 print: The maintenance call is not triggered.) |
о | о | о |
| Sys/ Panel |
0145 | Maintenance-Drum Meter Entry |
Sets the number of print-drum prints that triggers the maintenance-call message. | Setting range: 0 to 9999000 prints (The entered value must be 0 to 9999.) Unit: 1 (The value of 1 means 1000 prints.) Default: 0 (0 print: The maintenance call is not triggered.) |
о | о | о |
| Sys/ Panel |
0146 | Scan First | Prevents machine vibration caused by the master removal action from affecting the scanning quality. By default, the scanning action and the master removal action start at the same time. When this test mode is enabled, firstly the scanning action starts and then the master removal and master making actions start after the scanning action is completed. | Setting value: 0: Disabled <default> 1: Enabled |
о | × | × |
| Sys / Panel |
0149 | Authentication Enable/ Disable Selection |
Enables/Disables authentication.
|
Setting value 0: Authentication disabled 1: Authentication enabled <default> |
о | о | о |
| Sys / Panel |
0150 | Print Quantity Repeat Setting | Sets whether to retain the last count when the Auto Process function is OFF. | Setting value 0: Do not retain <default> 1: Retain |
о | × | × |
| Sys / Panel |
0151 | Print after Short Interval | Sets whether to enable gradual print speed acceleration after a short interval between printing jobs. | Setting value: 0: Disable gradual print speed acceleration «default for Japan> 1: Enable gradual print speed acceleration «default for overseas> |
о | о | о |
| Sys/ Panel |
0152 | "Lighten print" display control |
Specifies whether to display "Lighten print" in Functions and Custom Setting Mode. | Setting value 0: Not display «default> 1: Display |
о | о | о |
| Sys/ Panel |
0153 | Special Paper Ctrl Enable Control |
Specifies whether to display "Properties" - "Special Paper Ctrl". | Setting value 0: Not display «default> 1: Display |
о | × | × |
| Sys/ Panel |
0154 | Min. Print Quantity Control | Sets whether to allow the "Minimum Print Q'ty" setting in Custom Setting Mode and Properties to be edited. | Setting value: 0: Uneditable 1: Editable «default> |
о | о | о |
| Sys/ Panel |
0155 | Counter Action Control | Enables/Disables the copy and master counters (solenoid counter and software counter). * This setting is reset to the default when the power is turned off. |
Setting value: 0: Counter disabled 1: Counter enabled «default> |
о | о | о |
| Sys/ Panel |
0159 | "Warning" Display Control | Specifies whether to display a size warning (F02, F10, or F43) at the start of master making or printing. | Setting value: 0: Display the warning 1: Not display the warning «default> |
о | × | × |
| Sys / Panel |
0160 | Auto Multi-Up Recovery | Specifies whether to reactivate the Multi-Up Print setting after a Multi-Up Print operation is completed while the Auto Process function is OFF. | Setting value: 0: Do not reactivate (The Multi-Up Print setting stays OFF) «default> 1: Reactivate |
о | × | × |